Determine the aquifer transmissivity

Assignment Help Civil Engineering
Reference no: EM13559352

The initial piezometric head in a confined aquifer has a thickness of 11.6 m is 85.7 m above sea level. A well with a radius of 0.5 m pumps at a constant rate of 1240 m3/day. After the cone of depression has achieved equilibrium, the piezometric heads at two observation wells 40 and 95 m from the pumping well are measured as 78.9 and 83.4 above sea level, respectively. Also, the piezometric head in the pumping well during equilibrium remains at 46.6 m.

Determine (a) the aquifer transmissivity, (b) the radius of influence of the pumping, and (c) the total well losses in and around the pumping well.

Reference no: EM13559352

Questions Cloud

Calculate the amount you will have from this investment : You have just received $10,000 witch which you can do anything. You have decided to invest the money over a long period of time and then use it to make a down payment on a vacation home.
Find the total work done and also form a problem statement : A man climbing a staircase of height 10m carries a brief case weighing 100N, he placed a briefcase on each step before him, the numbers of steps are 5 of equal distance,after reaching the top step, he push his briefcase with a force of 50N with speed..
What is the hydraulic conductivity of the aquifer : An experiment was conducted to determine the hydraulic conductivity of an artesian aquifer. The piezometric heads at two points 150m apart were found to be 55 m and 48.5 m above a datum.
What should be the thickness of the confined aquifer : Consider two strata of the same soil material that lie between two channels. The first stratum is confined, and the second one is unconfined, and the water surface elevations in the channels are 24 m and 16 m above the bottom of the unconfined aquife..
Determine the aquifer transmissivity : The initial piezometric head in a confined aquifer has a thickness of 11.6 m is 85.7 m above sea level. A well with a radius of 0.5 m pumps at a constant rate of 1240 m3/day. After the cone of depression has achieved equilibrium, the piezometric head..
Calculate the hydraulic conductivity of the aquifer : A pumping well of 0.75-m radius fully penetrates an unconfined aquifer of 24-m thickness and produces at a rate of 10 L/s. After a long period of pumping well is 1.6 m. The drawdown in another observation well 60 m from the pumping wel
Estimate the weight of concrete in a four-lane highway : Estimate the weight of concrete in a four-lane highway segment that begins as a 3% grade climb from 1000 feet altitude to 4000 feet and then a 6% downgrade to 2500 feet
Highlight the area of the graph that represents work : Consider a piston-cylinder device. Within this device, a quasi-equilibrium process occurs for which the pressure changes according to the equation p = 300V2 + 1000 V + 1000, with p, pressure, in psfa, and V, volume
What length of the existing level highway must be reconstruc : At a railroad crossing, an overpass must be built centered over the tracks at a height of 24ft and be 200ft long. the existing highway has a design speed of 50mi/hr. what length of the existing level highway must be reconstructed to provide an approp..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the velocity and the volume flow rate of the steam

Steam enters a nozzle at 400oC and 800 kPa with a velocity of 10 m/s, and leaves at 300oC and 200 kPa while losing heat at a rate of 25 kW. For an inlet area 0f 800 cm2, determine the velocity and the volume flow rate of the steam at the nozzle ex..

  Determine normal stresses induced in steel and in concrete

The concrete post (Ec=3.6*10^6 psi and Ac= 5.5*10^-6/degrees F) is reinforced with six steel bars. each of 7/8-in diameter (Es=29*10^6 psi and As=6.5*10-6/ degrees F).

  What is the velocity of the projectile at the end of process

For simplicity assume the catapult consists of the piston-cylinder geometry (with the piston as the projectile) and that it is positioned horizontally. The steam initially occupies a volume of 1 liter at a pressure of 200 kpa.

  How to draw bending moment diagram

How to draw bending moment diagram for this shape and the value of the moment in critical sections assume that the distributed load (w) KN/M and the concentrated load

  Determine the adequacy of the design using basic principles

For the eccentric shear loading of the accompanying figure, 7/8 inch diameter A325 bolts are used in two vertical lines in a bearing-type (A325-X) connection. The loading is 10 kips dead load and 30 kips live load.

  Determine mag of force p required to maintain equilibrium

Collars A and B are connected by a 25 in long wire and can slide freely on frictionless rods. If a 60 lb force Q is applied to B. determine tension in wire when (black) x = 9 in and b) corresponding mag of force P required to maintain equilibrium ..

  Determine if flow will choke and the downstream water depths

(a) determine if the flow will choke and both the downstream and upstream water depths. (b) if there is also a 1 ft high step up in bottom elevation at the contraction, determine if the flow will choke and both the downstream and upstream water de..

  Determine the maximum tensil and compressive stresses in sec

The vertical portion of the press shown below consists of rectangle tube of wall thickness t=8mm. knowing that the press has been tightened on wooden planks being glues together until P = 20 kN, determine the maximum tensil and compressive stresses i..

  Determine the force required with an angle of 20 degrees

A 10 kg block is being pulled down a slope with an angle of 20 degrees and has a velocity of .2 m/s. Determine the force required

  When will drivers be able to see the full sign

A roadway has a 4% grade intersecting a -7% grade at at station 18+50.00. The grades are connected by an 800 foot vertical curve. A sign is proposed to be installed at Station 15+00.00. The bottom of the sign is 7 feet above the roadway.

  Calculate the torque and torsional shearing at the wall

a 31' solid circular bar of 2" diameter is fixed to a wall. it is made of aluminum of E=10*10^6. a 30" circular solid 1" diameter aluminum bar is welded to the 2" bar at a 30" centerline perpendicular relative to the other bar per the diagram.

  Determine what is the rate of leakage in gallons per day

An in-ground swimming pool may have a leak. The 30-ft by 10-ft by 5-ft (depth) pool is filled on June 1. On June 13, a hose, flowing at a rate of 10 gallons per minute, is used to add water to the pool. The hose is turned off after 1 hour.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd