Determine solids retention time and cell wastage flow rate

Assignment Help Civil Engineering
Reference no: EM13323258

Using the following assumptions, determine the solids retention time, the cell wastage flow rate, and the return sludge flow ratefor the Jambalaya shrimp processing plant WWTP

Assumptions:
Allowable BOD5 in effluent = 25.0 mg/l
Suspended solids in effluent = 30.0 mg/l
Wastage is from the return sludge Line
Yield Coefficent = 0.50 mg VSS/mg BOD5 removed
Decay rate of microorganisms = 0.075 d^-1
Inert Fraction of suspended solids = 30.0%

Reference no: EM13323258

Questions Cloud

Define why the solubility of different cations groups : Explain why the solubility of different cations groups can be affected by the acidification of their solutions
Declare a class with name cubicle : Declare a class with name Cubicle. The name stands for any rectangular prismatic solid body having three dimensions, i.e. length, width, and height.
What is the thinnest thickness the soap film : A soap bubble strongly reflects light of 463nm, wavelength, if the index of refraction of the film is 1.35, what is the thinnest thickness the soap film can be
Is the number positive or negative : if the machine is big endian and the number is an IEEE single precision floating point value, determine the decimal equivalent of the number stored at address 100.(you may leave your answer in scientific notation form, as a number times a power of..
Determine solids retention time and cell wastage flow rate : Using the following assumptions, determine the solids retention time, the cell wastage flow rate, and the return sludge flow ratefor the Jambalaya shrimp processing plant WWTP
How many rtts would take this tcp connection to transmit : How many RTTs would take this connection to transmit a 100-packet sized file, just by using TCP AIMD mechanism, when no packets are lost during the transfer? (Assume slow-start is not used)
What is the angle of deviation for the red ray : The index of refraction for violet light in silica flint glass is 1.65, and that for red light is 1.62. What is the angle of deviation for the red ray passing through a prism of apex angle
Compute how many drops of hcl are needed to reach : 50 ml of .001 molar naoh were titrated with .50 molar hcl, added with a dropper pipet. If each drop has a volume of .040 ml calculate how many drops of hcl are needed to reach the end point of titration.
Case study - periwinkle pty : Advise Periwinkle of its FBT consequences arising out of the above information, including calculation of any FBT liability, for the year ending 31 March 2014 and how would your answer to (a) differ if Emma used the $50,000 to purchase the shares hers..

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Write program that asks for diameter of two different sphere

Write a program that asks for the diameter of two different spheres. Then display to the user, the Maximum, Minimum, and Average volume of the spheres. Display this result in different lines of ONE message box by using VBCRLF.

  Compute the required stirrup spacing at the given location

At a certain location along the span, a reinforce concrete beam section with d=14 in. and b=10 in. is subject to a design shear of Vu=50k. Using No.4 stirrups, compute the required stirrup spacing at the given location. assume F'c=3 ksi and Fy=40 ..

  Determine the factor of safety with respect to shear failure

A footing 3m X 3m carries a pressure of 500 kN/ m2 at a depth of 1m in a sand substrate. The saturated unit weight of the sand is 20 kN/ m3 and the unit weight above the water table is 18 kN/ m3.

  What is the ratio of the magnitude of e2 to the magnitude

What is the ratio of the magnitude of E2 to the magnitude of E1? You may neglect the effects of gravity on the proton.

  Determine the controlling ct factor at the water temperature

A small city is evaluating disinfection requirements for their drinking water plant. With an average flow of 5 MGD and a peak flow of 9 MGD, determine the controlling CT factor (virus or giardia) when the water temperature is 23 degrees C.

  Find min valve-closure time to avoid creating water pressure

Water flows in a 100 m long pipe at 3 m/s. If the water temperature is 20 degrees C, determine the minimum valve-closure time to avoid creating water hammer pressures. What is the maximum water-hammer pressure that can occur

  Find modulus of elasticity of pavement for corner deflection

The pavement is on a base which has a modulus of subgrade reaction of 250 pci. A 17,000 lb corner load is applied (al is 7 inches). Using the revised Westergaard equations, find the modulus of elasticity of the pavement if a corner deflection of 0..

  Describe which would include a viable by-sell agreement

Each of the three partners realizes that in order for the firm to continue at the present rate of growth a realistic business continuation plan must be in place which would include a viable by-sell agreement between the shareholders.

  Which is estimated at 1 billion had that rate continued

World population 10,000 years ago has been estimated at about 5 million. what exponential rate of growth would have resulaed in the population in 1850 , which is estimated at 1 billion had that rate continued

  Design size of smoke vents in the ceiling with the objective

A storage room in an industry has a floor area of 30 m by 50 m and a height of 10 m. A garage door has a width of 3 m and a height of 3 m and the room has four windows that are 0.9 m by 0.9 m, situated at the height of 1 m from the floor.

  Elevation and stationing of the low point

A 1600 ft long sag verical curve (equal tangent) has a pvc at station 1200+00 and elevation o 1500 ft. the initial grade is -3.5% and the final grade is 6.5%. determine the elevation and stationing of the low point, pvi and pvt.

  Calculate the largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture. For the alloy, the plane strain fracture toughness is 24 and yi..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd