Determine remaining load carrying capacity of cracked beam

Assignment Help Civil Engineering
Reference no: EM13307280

a reinforced concrete beam with a section of 12 inches width and 24 inches depth is reinforced with 3no. 9 bars. fc'=5000psi and fy=60000psi. a 2 inch cover is used and the beam has a simply supported span lenght of 15ft. if the beam was found to have a cracks of 4inches at the bottom of mid span. chek whether the existing crack is safe.
determine the remaining load carrying capacity of this cracked beam.

Reference no: EM13307280

Questions Cloud

Determine kinetic energy after the stream has slowed down : A section view of a dam shown and water is stored at an elevation of 6 m above the base. the water flows through the dam in a concreate opening 2m high and 3 m wide. there are no losses or friction.
At what distance is the center of mass from the left end : If a 20kg mass hangs from the right side of a massless bar 5 meters in length and a 5kg mass hangs from the left side of the bar
Create a program that interviews the users : Create a program that interviews the users about their personal information, how many jobs they have and what the income is from each of their jobs. The program should then display back to the user the following items.
Find the radiation pressure on the mirror : A 23.2-mW laser beam of diameter 2.18 mm is reflected at normal incidence by a perfectly reflecting mirror. Calculate the radiation pressure on the mirror
Determine remaining load carrying capacity of cracked beam : a reinforced concrete beam with a section of 12 inches width and 24 inches depth is reinforced with 3no. 9 bars. fc'=5000psi and fy=60000psi. a 2 inch cover is used and the beam has a simply supported span lenght of 15ft.
Why is it that a profit-maximizing businessman : Question 2: Why is it that a profit-maximizing businessman would always raise prices when facing an inelastic demand curve, but might or might not raise prices when facing an elastic demand curve? Explain and justify your answers in detail.
Analyze the financial planning process for new ventures : Analyze the financial planning process for new ventures and speculate about which steps are the most difficult for new entrepreneurs to implement. State why they are the most difficult.
Determine the equivalent units for each factor of production : Determine the equivalent units for each factor of production and calculate the cost per equivalent whole unit for each factor of production
What voltage will be required for a current : A 162 Ω resistor is connected to a variable power supply. What voltage will be required for a current of 0.6 A to flow in the resistor

Reviews

Write a Review

Civil Engineering Questions & Answers

  Engineering societies based on the research

What are Engineering Societies based upon the research? List at least 10 discipline specific engineering societies along with their website addresses.

  Determine the flow rate of the oil

Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.

  Determine diameter of 200 m section commercial steel pipe

determine diameter of 200 m section commercial steel pipe (darcy's friction factor f = 0.0115) that carries a flow of 0.24 m^3/s and allowable head loss ove the section is 3.5 m.

  What is the speed that the observer at a records

Car B is driving straight toward the point O at a constant speed v. An observer, located at A, tracts the car with a radar gun. What is the speed |r(dot)B/A| that the observer at A records

  Determine the deflection of a simple uniformly loaded

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  Calculate the final temperature of xe in degree c

Two m^3 of xenon(Xe) are contained in a closed rigid tank at 70 degree C and 2 bar. The tank is heated to a pressure of 10 bar. Assuming that Xe behaves like an ideal gas with a specific heat ration of 1.7

  Calculate the cost per kg charged by these two suppliers

Our laboratory plans to use one, 10-liter tank of refrigerant 134a every week. So off you go to check the cost of fill-ups at the two possible suppliers. At Chem Mart, the filled tank is returned to you at 10 bar and 90 C for $10.00.

  Determine what is the departure rate at a parking lot

The arrival rate at a parking lot is 6 veh/ min. Vehicles start arriving at 6: 00 P. M., and when the queue reaches 36 vehicles, service begins. If company policy is that total vehicle delay should be equal to 500 veh-min

  Determine the moment of the couple formed by the two forces

Two parallel 40-N forces are applied to a lever. Determine the moment of the couple formed by the two forces (a) by resolving each force into horizontal and vertical components and adding the moments of the two resulting couples

  Time inventory system for a product

How appropriate might a just in time inventory system be for a product such as roller skates?

  How many 1-inch diameter steel bolts are required to hold

The two cylinder containers are joined by bolting their flanges together. How many 1-inch diameter steel bolts are required to hold the cylinders together when the assembly is subjected to an internal pressure of 200 psi

  Describe will the car stop before hitting the wall

A car weighing 4000 pounds strikes the stopping barrier depicted below head on at a speed of 70 mph. The stopping force in the barrier is a function of how far the car penetrates into the barrier.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd