Determine line current drawn from the three phase supply

Assignment Help Electrical Engineering
Reference no: EM13284944

An automatic automotive spray painting system consists of conveyors, spraying, dust and overspray extraction fans with electrostatic and water walls, finishing with baking ovens. This system is connected to a 415V, 50 Hz three phase and has been three divided into three balanced loads, as follows:

LOAD 1 (DELTA): 150 kVA at a power factor of 0.60 lagging;
LOAD 2 (STAR): 44 kW at a power factor of 0.55 leading;
LOAD 3 (STAR): ZR = ZW = ZB = 3.5 + j 2.75 O;


(i) Draw a diagram of the loads.
Determine: (ii) The apparent power (kVA), active power (kW) and reactive power (kVAr) of each of the three loads.
(iii) The total apparent power kVA, total active power (kW) and the total reactive power (kVAr) of the loads.
(iv) The capacitive kVAr required to correct the overall supply power factor to 0.85 lagging.
(v) The line current drawn from the three phase supply before and after power factor correction.

Reference no: EM13284944

Questions Cloud

How does the bandwidth of the pci bus compare : The PCI bus found in many computers transmits 64 bits per clock cycle at 33MHz. How does the bandwidth of the PCI bus compare to the serial FireWire (IEEE 1394) serial bus specification, which is 400 Mbits per second
How to compute the composition of the vapor : Calculate the composition of the vapor (mole fraction of each component) that is in equilibrium in the solution at the boiling point of this solution
Determine the value produced at the primary output : Draw a digital circuit consisting of a 2-input AND gate and three inverters, where an inverter is connectedf to each of the AND gate's input and its output. For each of the four possible combinations of inputs applied to the two primary inputs of ..
What is the reason for the long run equilibrium of a firm : What is the reason for the long run equilibrium of a firm in monopolistic competition to be associated with zero profit?
Determine line current drawn from the three phase supply : (i) Draw a diagram of the loads. Determine: (ii) The apparent power (kVA), active power (kW) and reactive power (kVAr) of each of the three loads. (iii) The total apparent power kVA, total active power (kW) and the total reactive power (kVAr) of the ..
Compute half life of n2o5 and b : Calculate the half life of N2O5 and B. how long does it take for the N2O5 concentration to drop one tenth of its original value. * I believe the half life is 10,000 seconds for part A. But I am having trouble with part B.
Find the price of a call option on the stock : The current price of a stock is $21. In 1 year, the price will be either $26 or $14. The annual risk-free rate is 3%. Find the price of a call option on the stock that has a strike price is of $25 and that expires in 1 year.
Find an expression for the bullets initial speed : You have been asked to design a "ballistic spring system" to measure the speed of bullets. Find an expression for the bullet's initial speed
The decomposition of no2 is second order in the reactant : If a vessel containing NO2 has an initial concentration of 2.8 x 10-2 mol/L, how long will it take for 75 of the NO2 to decompose? The decomposition of NO2 is second order in the reactant and the rate constant is 1.1 L/mol x s.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Frequency range and local oscillator frequency

Frequency Range, Local Oscillator Frequency, Image Frequency, and Attenuation, A radio receiver for the AM broadcast band covers the frequency range 550 to 1600 kHz. The IF frequency is 455 kHz and the local oscillator is above the received signal..

  Design a 4-bit serial adder with vhdl code or schematic

design a 4-bit serial adder (VHDL code or schematic) which includes two shift registers and a single full-adder to perform the following functionality with proper timing controls. Two 4-bit inputs A and B will be set by eight switches on your Xili..

  Provide example of resistor de-rating curve from manufacture

Identify and describe three different ways to manufacture resistors. These variations can be "form factor" or the technique used to establish the resistance. Provide an example of a resistor de-rating curve from a manufacturer

  Give the enthalpy change h for the given reaction

Suppose 33 mL of 1.20 MHCl is added to 42 mL of a solution containing excess sodium hydroxide, NaOH, in a coffee-cup calorimeter. The solution temperature, originally 25.0C, rises to 31.8C.

  Determine amount of energy used during one evening in units

Alfredo deDarke sleeps with a 7.5-Watt night light bulb on. He turns it on before getting in bed and turns it off 8 hours later. a. Determine the amount of energy used during one evening in units of kiloWatt*hours.

  Draw a relay construction diagram

Draw a relay construction diagram and briefly explain the operation of a relay.

  Find by what angle does i lead another current

A sinusoidal current is zero and increasing at t = -3.33ms; the next zero crossing occurs at t = 6.67ms. a) calculate T, F, and W. b) if i(0) = 25.98 A, Find i(t). c) By what angle does i(t) lead another current i(t) = 5 sin (wt - 5°) A.

  Find the internal resistance of the dc power suppy

A 50 V DC power supply is connected to a 100 Ohm load resistor. The tested current flowing through the resistor is 0.49 A. find the internal resistance of the DC power suppy.

  How to calculate nf in term of a pure ratio

The NF (dB) is defined as 10log(SNRin/SNRout) - in the unit of dB. If we are given the values of SNRin and SNRout in dB unit, how do we calculate NF (dB) in terms of dB, and how do we calculate NF in term of a pure ratio

  How arsenic atoms are fully ionized at room temp

A Silicon wafer has a uniform doping density of 8 xl018 atoms cm-3 of Arsenic and 2.5 x 1019 atoms cm-3 of Phosphorus. Assume that all Arsenic atoms are fully (100%) ionized at room temperature but the Phosphorus atoms are 80% ionized.

  Find the amplitude of the output signal if the 12khz input

at the frequency f=12khz, a filter is designed to attenuate the input signal by 78db, find the amplitude of the output signal if the 12khz input has an amplitude of 1V.

  What would be the percentage change in field intensity

If the power of a 500-kHz transmitter is increased from 150 W to 300 W, what would be the percentage change in field intensity at a given distance from the transmitter. What would be the decibel change in field intensity.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd