Determine if it is possible for pressure of the refrigerant

Assignment Help Mechanical Engineering
Reference no: EM131015299

A piston-cylinder assembly contains 1 lb of Refrigerant 134a initially as saturated vapor at 10°F. The refrigerant is compressed adiabatically to a final volume of 0.8 ft3. Determine if it is possible for the pressure of the refrigerant at the final state to be

(a) 60 lbf/in.2
(b) 70 lbf/in.2

Reference no: EM131015299

Questions Cloud

Does claimed performance violate principles of hermodynamics : A patent application describes a device that at steady state receives a heat transfer at the rate 1 kW at a temperature of 167°C and generates electricity. There are no other energy transfers. Does the claimed performance violate any principles of..
We are even on the cusp of a 6th mass extinction event : Ensure that each of the questions or topics listed above are addressed with accurate information. Grammar, spelling and syntax are correct.
Find all horizontal and vertical asymptotes : Prove the following statements using the precise definition of the limit. Find all horizontal and vertical asymptotes of the following functions. If there are no asymptotes, say so.
What patient resides in california : What patient resides in California? What is the patient number? Who is Sofia Yakaria Pallares' provider? What credentials does her provider have
Determine if it is possible for pressure of the refrigerant : A piston-cylinder assembly contains 1 lb of Refrigerant 134a initially as saturated vapor at 10°F. The refrigerant is compressed adiabatically to a final volume of 0.8 ft3. Determine if it is possible for the pressure of the refrigerant at the fi..
Present value of costs : The Aubey Coffee Company is evaluating the within-plant distribution system for its new roasting, grinding, and packing plant. The two alternatives are (1) a conveyor system with a high initial cost, but low annual operating costs, and (2) several..
Determine the change in specific entropy of the refrigerant : One kilogram of Refrigerant 134a contained within a piston-cylinder assembly undergoes a process from a state where the pressure is 7 bar and the quality is 50% to a state where the temperature is 16°C and the refrigerant is saturated liquid. Det..
What two cellular structures would you target : Now, respond to your classmates and comment on the potential effectiveness of the drug they have selected, and offer potential pitfalls of the drug
Determine the heat transfer and the work : A gas initially at 14 bar and 60°C expands to a final pressure of 2.8 bar in an isothermal, internally reversible process. Determine the heat transfer and the work, each in kJ per kg of gas, if the gas is (a) Refrigerant 134a, (b) air as an ideal ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Aluminum oxide al2o3 has a surface energy of 1 jm2 estimate

aluminum oxide al2o3 has a surface energy of 1 jm2 estimate the maximum amount of energy jg that is available for

  What is its temperature and quality

R134a rests in a compressed fluid can at 120psia, and a specific volume of 0.38ft3/lbm. What is its temperature and quality? Half of the mass is now vented off to the atmosphere. The can is allowed to exchange heat with the surroundings at 100°F unt..

  Calculate the theoretical diameter of the pipe

Calculate the theoretical diameter of the pipe; the nominal pipe diameter chosen from the table; and the actual average velocity in the nominal pipe - Calculate Reynolds number for the process and hence the head loss due to friction.

  Assuming the water heater acts as a heat sink having an

cold water at 10degc enters a water heater at the rate of 0.02 m3min and leaves the water heater at 50degc. the water

  Determine the power devolped in kw the exergy destruction

air at 5 bar 500 k and a volumetric flow rate of 8 m3s enters an insulated turbine operating at steady and exits with a

  Determine the exit temperature in degrees

Steam at 3MPa and 400C enters an adiabatic nozzle steadily with a velocity of 40m/s and leaves at 2.5MPa and 300m/s. Determine the exit temperature in degrees C. the ratio of the inlet to exit area

  Copper disk is placed in a bath of cooling fluid

In a manufacturing process, a copper disk is placed in a bath of cooling fluid. The copper disk has a 5 cm radius and a 1 cm thickness. The initial temperature of the copper disk is 450 degrees Celsius. The thermal conductivity, density, and specific..

  One kilogram of water fills a 150-l rigid container at an

one kilogram of water fills a 150-l rigid container at an initial pressure of 2 mpa. the container is then cooled to 40

  The city of houston has a water filtration system that

the city of houston has a water filtration system that consists of a large rigid tank with a single 1.5m diameter inlet

  How do we use principles of superposition to define the

give a clear explaination on shear force and bending moment distributions using singularity functions?how do we use

  Measure the pressure inside

A mercury manometer (r = 13,600 kg/m3) is connected to an air duct to measure the pressure inside. The difference in the manometer levels is 15 mm, and the atmospheric pressure is 100 kPa.

  Plot the total mass in the tank

Plot the total mass in the tank, in kg, and the amount of heat transfer, in kJ, versus the final quality x ranging from 0.2 to 1.0

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd