Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
For finding the elevation of point C the Azimuth Angle from poit A to C is measured as 76deg ?15'00". The height of the instrument during this measurement was 1.60m From the same setup from point A, the zenith angle and slope distance toward point B are measured as 83deg 32'30" and 186.23m respectively, while the elevation of point B is 315.34m AMSL. The Height of the target at B was set at 2.00m the horizontal angles BAC and CBA are measured as 60deg 37'54" and 81deg 59'06"
Determine:
a)the horizontal distance AB and elevation of point A
b)the horizontal distance AC
c)and Elevation of point C
Ammonium (NH4+) is a weak acid with a pKa of 9.26. The dissociation is: NH+4 NH3 + H+. Calculate the mass of ammonium added to 1 L of water in order to obtain a pH of 4 at equilibrium.
The cart has a velocity of 4 ft/sec to the right. Determine the angular speed N of the wheel so that point A on the top of the rim has a velocity (a) equal to 4 ft/sec to the left, (b) equal to zero, and (c) equal to 8 ft/sec to the right
A temporary diversion has been constructed on a highway of +4 percent gradient due to major repairs that are being undertaken on a bridge. The maximum speed allowed on the diversion is 10 mph.
Vehicles arrive at a toll bridge at a rate of 430 veh/hr (the time between arrivals is exponentially distributed) Two toll booths are open and each can process arrivals (collect tolls) at a mean rate of 10 seconds per vehicle
Due to atmosphere drag, the deceleration equation is 60a=588.6-30v^2 in m/s^2. Find the velocity at which he lands on the ground. This velocity is referred to as terminal velocity, which is found by letting the distance of the fall (y) go to infin..
Two identical squares (each18x18mm ) sit on the x axis and are joined at the y axis to form a rectangle. What is the rectangle's product of inertia
Draw a plan of a typical strip mine showing all operational features and equipment and why is the working slope of an open pit usually much flatter than the final slope?
A soil specimen has a water content of 18% and a wet until weight of 118.5 lb/ft. The specific gravity of solids is found to be 2.72. Find the dry unit weight, void ratio, and degree of saturation.
A horizontal het of water at 5 degrees celsius strikes a block and is deflected upward 30 degrees. The mass flow rate of the water is 1.75 kg/s. The mass of the block is 1.30 kg. The jet has a cross sectional area of 10 cm^2.
A rectangular copper specimen (Table 1--> E=120GPa) is loaded in tension of 300MPa and then the load is removed. The total plastic strain in the unloaded specimen is e=0.25.
The cross sectional dimensions of a 4-ft-long wood member at 30% moisture content is 1.5 in. x 7.5 in., and its weight is 11 lb. At oven-dry condition, its dimensions and weight are 1.35 in x 6.8 in., and 10.2, respectively. What is its specific g..
A fully enclosed cylindrical fuel tank with a diameter of 6.00 meters and a height of 8.00 meters has a manufacturing tolerance of +/- 0.04 meteres for each of these dimensions.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd