Determine at that instant the radial and transverse compont

Assignment Help Civil Engineering
Reference no: EM13543406

1.a .3 L glass of water at 20 deg C is to be cooled with ice to 5 deg C determine how much ics needs to be addeed to the water in grams if the ice is at a) 0 degC and b)-20 deg C also determine how much water would be needed if the cooling is to be done with cold water at 0 deg C the melting temperature and the heat of fusion of ice at atmospheric pressure are 0 deg C and 333.7 kJ/kg respectively and the density of water is 1 kg/L

2.A 1.5-kg collar is attached to a spring and slides without friction along a circular rod in a vertical plane. Knowing that the tension in the spring is70 N and the speed of the collar is 3.8 m/s as it passes through point A, determine, at that instant, the radial and transverse components of acceleration of the collar.

Reference no: EM13543406

Questions Cloud

Determine the initial and final temperatures : A mass of 5 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 125 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase
Determine the heat loss or gain during this process : A piston-cylinder device contains helium gas initially at 150 kPa, 20 degrees C, and 0.5 m^3. The helium is now compressed in a polytropic process (PV^n = constant) to 400 kPa and 140 degrees C. Determine the heat loss or gain during this process.
What is the magnitude and direction of the resultant force : Water under a gage pressure of 350kPa flows with a velocity of 5 m/s through a right-angled bend that has a uniform diameter of 250 mm
What would be the resultant force on the plate : A 40-mm-diameter jet has a velocity of 25 m/s. If this jet were to strike a large flat plate normally, what would be the resultant force on the plate?
Determine at that instant the radial and transverse compont : 1.5-kg collar is attached to a spring and slides without friction along a circular rod in a vertical plane. Knowing that the tension in the spring is70 N and the speed of the collar is 3.8 m/s as it passes through point A,
Find the pressure at the forward and rear corners along the : A closed box with horizontal base 6m x 6m and height of 2m is half-filled with water and is accelerated Ax=4.9 m/sec^2 and Ay=-2.4 m/sec. find the pressure at the forward and rear corners along the bottom.
Draw the influence line for the tension in the cable as : Draw the influence line for the tension in the cable as a point load travels across the beam. Find the maximum tension in the cable due to a live point load of 6 k on the beam.
Determine the adjusted asd values associated with the : A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D + S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.
What would be the values of density and water content if the : A soil has a bulk density of 1.91 Mg/m^3 and a water content of 9.5%. The value of Gs is 2.70. Calculate the void ratio and degree of saturation of the soil. What would be the values of density and water content if the soil were fully saturated at th..

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What is the elevation at point 2 and the pressure at point 3

A buried stock-water pipeline conveys water from a water source at Point 1, rises to pass up and over the peak of a hill (Point 2) before falling to Point 3 in the pipeline some

  Determine the average value of k in meter per sec

A stopwatch was started when h was 501 mm and read 17.6 seconds when h was 244 mm; the test was repeated for a drop from 254 mm to 97 mm and the time was 22.4 seconds.

  Determine the decay rate constant for the die-off of anthrax

The results of his experiment are tabulated below. Assuming the experiment was conducted in a completely-mixed batch reactor, determine the decay rate constant for the die-off of anthrax.

  Determine what diameter should the spherical balloon have

A balloon is to be used to carry meteorological instruments to an elevation of 15,000 ft where the air pressure is 8.1 psia. The balloon is to be filled with helium, and the material from which it is to be fabricated weighs 0.01 lbf/ft^2.

  Thermal conductivities of aluminum and copper

The aluminum end and the copper end are maintained at temperatures of 50°C and 260°C, respectively. The thermal conductivities of aluminum and copper are 205 and 385 W/m · K, respectively. The temperature of the aluminum-copper junction in the rod..

  What fraction of the flue gas stream would need to be bypass

The company engineer decides that this is too good, that it is not necessary to be this efficient, and proposed that part of the flue gas be bypassed around the electrostatic precipitator so that the recovery of fly ash (particulates) from the flu..

  What percentage increase will be in the flow from house

suppose a family of four, living in a home with an area of 100x5oft connects its stormwater drain to the sewer. Assume that 1in of rain falls over 1 day. what percentage increase will there be in the flow from their house over the dry weather flo..

  Calculate the length of side ut and the area of the plot

The following data are taken: RU=130.0m, RS=120.0m, ST=90.0m, angle RST= 115 degrees, and angle RUT= 100 degrees. Calculate the length of side UT and the area of the plot.

  Find the total energy cost and savings from cfl bulbs

A CFL bulb that puts out as much light as a 60-W incandescent bulb might costs $10, compared to about $1 for the incandescent bulb. But CFL bulbs are expected to last (on average) 15,00 hours, compared to about 1000 hours for an incandescent bulb.

  Determine the flow rate above the pipe

A 2-inch diameter glass pipe is connected to a pipe network in which the pressure is 70 psig. If the length is 300 feet and the outlet is 10 feet above the pipe, determine the flow rate.

  Question 1 what is the difference between labor cost and

question 1. what is the difference between labor cost and labor pro-ductivity? use a sketch to illustrate.question 2.

  Determine diameter of solid shaft if it is to transmit 50hp

If the allowable shear stress is 15ksi, determine the diameter of a solid shaft if it is to transmit 50hp at a frequency of (a) 900rpm, (b) 1800rpm

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd