Determine a the pressure volume and temperature at the

Assignment Help Mechanical Engineering
Reference no: EM13631689

In an ideal dual combustion cycle conditions at the commencement of adiabatic compression are 93 kPa, 0.05 m3 and 24°C, respectively. The adiabatic compression volume ration is 9:1. The constant volume heat addition pressure ratio is 1.5 and the constant pressure heat addition volume ratio is 2. If Cp = 105 kJ/kg-K and Cv = 0.775 kJ/kg-K, determine (a) the pressure, volume and temperature at the state points of the cycle (b) the thermal efficiency of the cycle (c) the work done per cycle. Solution for b) 48% Solution for c) 44.4 kJ.

Reference no: EM13631689

Questions Cloud

A company studying the productivity of their employees on a : a company studying the productivity of their employees on a new information system was interested in determining if the
After 10 lbhr of the oil is removed from the potato chips : after 10 lbhr of the oil is removed from the potato chips in the separation unit what is the mass fraction of oil on
A biconvex ice lens is made so that the radius of curvature : a biconvex ice lens is made so that the radius of curvature of the front surface is 12.3 cm and that for the back is
Explain viscous damping with a sketch provide a model that : explain viscous damping with a sketch. provide a model that may be used in studying vibrations. given m 2 b 8 and k
Determine a the pressure volume and temperature at the : in an ideal dual combustion cycle conditions at the commencement of adiabatic compression are 93 kpa 0.05 m3 and 24degc
For example the probability that the economy will be in : suppose that the percentage annual return you obtain when you invest a dollar in gold or the stock market is dependent
A square loop of dimensions 2a x 2a lies in the xy plane : a square loop of dimensions 2a x 2a lies in the xy plane with its center at the origin and sides parallel to the x and
A refrigerator should remove 500 kj from some food assume : a refrigerator should remove 500 kj from some food. assume the refrigerator works in a carnot cycle between -10 degrees
A medical researcher wishes to determine the percentage of : a medical researcher wishes to determine the percentage of females who take vitamins. he wishes to be 95 confident that

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the minimum pump power required to pump water

determine the minimum pump power required to pump water from one reservoir to another at an elevation of 110 m above

  Fully draw shear force and bending moment diagrams noting

derive the equation for maximum deformation of a beam in 3 point bending following steps will be helpfula fully draw

  The low-temperature reservoir of a carnot heat engine is

the low-temperature reservoir of a carnot heat engine is at 10 c. to increase the efficiency of this heat engine from

  Determine the cooling capacity of the device and the actual

consider the steady operation of a refrigeration package for a shipping container on a train truck or ship. the package

  How high on the wall will the ladder reach

a 14-ft long ladder leans against a wall with the bottom of the ladder placed 4ft from the base of the wall. how high on the wall will the ladder reach.

  Determine the angular velocity theta dot of the combined

a wad of clay mass m1 with an initial horizontal velocity v1 hits and adheres to the massless rigid bar which supports

  What are the standard s.i. and english based units

What are the standard S.I. And English based units for reporting strain? What are the standard S.I. And English based units for reporting Youngs Modulus?

  The average plate temperature of a flat plate of length l

the average plate temperature of a flat plate of length l with constant heat flux with air at 20?c flowing over it at a

  Determine the angular velocity of rod bd

Knowing that crank AB has a constant angular velocity of 160 rpm counterclockwise, determine the angular velocity of rod BD and the velocity of collar D when a. delta=0, b. delta = 90.

  Derive an expression for the intermediate temperature t in

two reversible power cycles are arranged in series. the first cycle receives energy by heat transfer from a reservoir

  Find the maximum load on bevel gear and shaft

You have a bevel gear and shaft and you have to find the maximum load that can be applied on it.

  The flow rate is 80 liters per second and pressure is

water flows through a 20-cm commercial steel pipe at 20 degrees celsius. the flow rate is 80 liters per second and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd