Determine the principal stresses on an element from the

Assignment Help Mechanical Engineering
Reference no: EM13627150

A thin-walled, closed end, cylindrical pressure vessel for jet fighter lubricant with spherical end caps is internally pressurized to 500 psi. if the mean diameter is 60.0 inches and wall thickness 1.0 inch, determine:

a) the principal stresses on an element from the cylindrical portion of the tank surface, sketch mohr's circle andsketch all principle stresses.

b) the principal stresses on an element from a portion of the spherical end caps, sketch mohr's circle, and sketch all principle stresses.

Reference no: EM13627150

Questions Cloud

The ball then slides along the table and makes an elastic : a cue ball mass 0.160 kg is at rest on a frictionless pool table. the ball is hit dead center by a pool stick which
What is your gravitational potential energy at the planes : you fly from bostons logan airport at sea level to denver at an altitude of 1.6 km. take your mass as 65 kg and the
Which of the following is the best reason for a project : which of the following is the best reason for a project team that is updating a clinical protocol to start by looking
A cone with a base radius of r contains a charge inside its : a cone with a base radius of r contains a charge inside its surface. the flux through the curved portion of the cones
Determine the principal stresses on an element from the : a thin-walled closed end cylindrical pressure vessel for jet fighter lubricant with spherical end caps is internally
A solenoid 300 cm long and with a cross-sectional area of : a solenoid 30.0 cm long and with a cross-sectional area of 0.600 cm2 contains 460 turns of wire and carries a current
Assume the spear gun barrel is 180 m above the water : on a safari you are spear fishing while wading in a river. you observe a fish gliding by you. if your line of sight to
Determine the ratio db for which a the maximum stress will : a couple m will be applied to a beam of rectangular cross section that is to be sawed from a log of circular cross
The quality of evidence in support of a recommendation : the quality of evidence in support of a recommendation depends on which of the following?a. the p values of the

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the time needed for the velocity

determine the time needed for the velocity to become v=vf. initially the particles falls from rest.

  Compute a values for p u v and d in the english engineering

the reynolds number re is a dimensionless number used in fluid mechanics and is defined as repvdu where p is the fluid

  Calculate the required heat transfer to or from the reactor

it is highly desirable to make benzene from ethane from shale gas in a continious vapor-phase reaction3c2h6 --gt c6h6

  Its about how to measure an increase in wind velocity

its about how to measure an increase in wind velocity through a restriction.it starts with an area that is 17 wide by

  A 3 m x 3 m x 24 m room losses heat through the walls at a

a 3 m x 3 m x 2.4 m room losses heat through the walls at a rate of 520 w. determine the final temperature of the room

  Calculate the velocity v of the collar

Calculate the velocity v of the collar as it hits the stop at B if it is elevated from rest at A by the action of the constant 40-N force in the cord. The cord is guided by the small fixed pulleys.

  Calculate a the power required by the compressor in kw b

he vapor compression heat pump operates at steady state using refrigerant 22 whose flow rate is 6kgmin. the heat pump

  Knowing that at the instant shown assembly a has a

knowing that at the instant shown assembly a has a velocity of 9in.s and an acceleration of 15 in.s2 both directed

  Knowing that 1 l ie one liter of regular gas provides 348

a 1500 kg car is traveling up on a road with a slope of 15 i.e. rise of 15 on a run of 100 at a constant speed. knowing

  Explain the true altitude of the plane above sea level

What is the true altitude of the plane above sea level? What would be the indicated altitude after landing at an aerodrome located at sea level? (Gas const = R=288 J/KgK)

  How much error would one expect in determining the

how much error would one expect in determining the specific enthalpy by applying the incompressible-liquid

  The plank cde has a mass m15kg and is rest on a small pivot

the plank cde has a mass m15kg and is rest on a small pivot at d. a block a of mass 55 kg is resting on point c. a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd