User Account

All Pages

Determine a the time required for the train to travel the

Assignment Help Mechanical Engineering
Reference no: EM13636819

A commuter train traveling at 40 mi/ h is 3 mi from a station. The train then decelerates so that its speed is 20 mi/ h when it is 0.5 mi from the station. Knowing that the train arrives at the station 7.5 min after beginning to decelerate and assuming constant decelerations, determine ( a) the time required for the train to travel the first 2.5 mi, ( b) the speed of the train as it arrives at the station, ( c) the final constant deceleration of the train.

Reference no: EM13636819

Questions Cloud

An astronaut floating in space is separated from his ship : an astronaut floating in space is separated from his ship. his mass is 85.0kg and he is 10.0m for his ship. he throws a
Calculate the maximum pressure that the walls must : an engine operates on an air-standard otto cycle. the pressure and temperature at the beginning of the compression
A sample of air contains 7275nitrogen 2645 oxygen 005 : a sample of air contains 72.75nitrogen 26.45 oxygen 0.05 carbon dioxide and 0.75 argon byvolume. how many molecules of
A 630-o resistor is connected in parallel with a 1200-o : a 63.0-o resistor is connected in parallel with a 120.0-o resistor. this parallel group is connected in series with a
Determine a the time required for the train to travel the : a commuter train traveling at 40 mi h is 3 mi from a station. the train then decelerates so that its speed is 20 mi h
A bar of 24-karat pure gold is supposed to be completely : a bar of 24-karat pure gold is supposed to be completely solid. to check this a scientist takes the bar into the lab.
Will the reported molar concentration of the sodium : pure potassiom hydrogen phthalate is used for standardization of the sodium hydroxide solution. suppose that the
Assuming that the force exerted by the pitcher on the ball : major league baseball training camps are now just beginning. given a baseball with a mass of 9 ounces estimate the work
If the stick loses half of its angular velocity during the : a stick of mass m and length l is pivoted at an end. it is held horizontal and then released. it swings down and when

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The airplane is cruising at m023 with an angle of attack

a flying wing has a swept symmetric airfoil with a planform area of 3700 sq ft a root cord at the airplane centerline

  What is the weight of the rover as it rolls off the landers

a robotic-wheeled vehicle that contains science instruments is used to study the geology of mars. the rover weighs 408

  A fenced enclosure consists of a rectangle of length l and

a fenced enclosure consists of a rectangle of length l and width 2r and a semicircle of radius r as shown in figure

  A structural compenent is formed with aluminum alloy

a structural compenent is formed with aluminum alloy 6061-t6 with youngs modulus e68.9 gpa and shear modulus g 26 gpa.

  A double-acting duplex pump with 65 in liners 25 in rods

a double-acting duplex pump with 6.5 in liners 2.5 in rods and 18 in stokes was operated at 2000 psig and 20 cyclesmin

  The truck travels in a circular path having a radius of 50

the truck travels in a circular path having a radius of 50 m at a speed of 4 ms. for a short distance from s 0 its

  What is the work required kjkg in the first compressor of

methane is to be compressed from 0.05 mpa and -120degf to 5 mpa in a two-stage compressor. in between adiabatic

  How long will it take for the austenite to pearlite

suppose that a steel of eutectoid composition is cooled to 550 degrees celcius from 760 degrees celcius in less than

  The water leaves the pump at a pressure of 14mpa and a

water at a temperature of 40 c and a pressure of 100 kpa enters a pump at the rate of 50000 kghr. the water leaves the

  Show that the moment of inertia of n particles each of mass

use the principle of angular momentum to eventually derive the moment of inertia integral. for each case find the

  A new prototype proven to perform with an isp of 1000s but

when deciding what propulsion system is most appropriate for a mission thrust and isp are not the only parameters that

  The r-134a is then heated to a final temperature of 30

r-134a is contained in a vertical cylinder fitted with a frictionless piston and a set of stops and the volum is 0.05m3

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd