Design value for the molded friction material and steel disk

Assignment Help Mechanical Engineering
Reference no: EM13212095

a disk clutch is to be designed for transmitting a torqueof 85N.m space restrictons limit the outside disk diameter to 100m.m.Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?

Reference no: EM13212095

Questions Cloud

Determine the buyers responsive to price changes : Recent trends in teen smoking are considered tobe positive by those who advocate for a reduction in teen smoking. The decline is attributed to government policy that restricts advertising that targeted children, for example the Jo Camel ads and bi..
Explain compound a optically active with a formula : Compound A, optically active, with a formula of C6H14O reacts with Na2Cr2O7 in H2SO4 forms a new compound B with formula C6H12O and is optically active
Find the final condition of steam : Steam at 10bar and 0.95 dry flows at 130 m/sec in a pipe. It is throttled to 8 bar and the flow rate is 12 kg/sec. Assuming velocity in the pipe on the down stream side of the valve is 160 m/sec. Find the final condition of steam and the pipe diam..
Which good would experience the largest decline in demand : Suppose there are two goods (a snob good and a bandwagon good), each priced at $100. If I were to increase the price of both goods by $50, which good would experience the largest decline in the quantity demanded by consumers.
Design value for the molded friction material and steel disk : Design value for the molded friction material and steel disks to be used 0.06 and pressure max=1400kpa. Determine appropriate values for the disk inside dimmeter, the total number of disks and the actuating force?
What is the actual strain : You have a 120 Ω quarter bridge 2 wire set up with Sg=2.10 and an unknown lead wire resistance. A 59880Ω calibration resistor is switched in parallel to the gage only and a recording instrument is set to give a -100 mm deflection for this calibrat..
What would be the cost minimizing combination of capital : Given the following production function with two inputs, Capital (K) and Labor (L), whose input prices are $1 each. Suppose the company needed to produce 50 units. What would be the cost minimizing combination of capital and labor needed
Find what income elasticity of demand was last week : The demand for pencils by New York University students at the bookstore is given by the following equation, , where I is the average income of nyu students, in dollars per week, Q pencils is the quantity of pencils sold per week.
Define cyclohexane and cyclopentane or ehylene oxide : Make the compounds listed from an alkyl halide having four carbons or less, with no functional groups but it can be branched, or cyclohexane, cyclopentane, or ehylene oxide.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the minimum no of teeth required

Determine the minimum no of teeth required on pinion in order to avoid interference which is to gear with 1 a wheel to give a gear ratio of 3 to 1

  Serpentine belt drive analysis and design

Determine the natural frequencies of the system-For the baseline system and find a design that changes the ?rst two natural frequencies more than any of the previous slight modi?cations.

  Explain fluid statics- submerged submarine

Fluid Statics: Submerged Submarine, A submarine is at a depth of 2000 ft from the water surface. The atmospheric pressure above the water is at 14.7 psia

  Determine the natural frequencies of the system

Determine the natural frequencies of the system. For the baseline system I get natural frequencies at the following engine speeds: 435, 2026, 2818, 5225, 7093, 10245, and 12153 rpm.

  Determine the turbine work output

Determine (a) the turbine work output, in kJ/kg, and (b) the thermal efficiency of the cycle. Also, show the cycle on a T-s diagram with respect to saturation lines.

  Explain a car and a high speed trian at constant speeds

A car and a high -speed trian at constant speeds. three seconds after the train passes under the highway bridge the car crosses the bridge.

  Diameter sphere is embedded in insulation

A 4 m diameter sphere is embedded in insulation. The sphere contains a liquid-ice mixture maintained at 0 deg C. The ambient temperature surrounding the insulation is 25 deg C.

  What is the airspeed of the plane

The airspeed of an aeroplane is measured with a Pitot tube. The plane is flying at an altitude of 10000m, and the Pitot tube measures a gauge pressure of p = 10kPa. What is the airspeed of the plane?

  Explain a piston-cylinder device initially contains

A piston-cylinder device initially contains 50L of liquid water at 40 degrees C and 200kPa. Heat is transferred to the water at constant pressure until entire liquid is vaporized.

  Explain single degree of freedom vibration problems

Single degree of freedom vibration problems with forcing functions, Need help with this Undergraduate problem where two dampers are in series.

  Explain square steel bar subjected to transverse biaxial

Consider a 4-in square steel bar subjected to transverse biaxial tensile stresses of 20 ksi in the x direction and 10 ksi in the y direction.

  The gap between them is filled with molten polymer

Two flat, rectangular plates with a lateral dimension w*l lie parallel, one above the other, a distance h apart. The gap between them is filled with molten polymer.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd