Design the basic interface circuit for a temperature sensor

Assignment Help Electrical Engineering
Reference no: EM13229437

Design the basic interface circuit (using an op amp) for a temperature sensor that covers a range of 0 degrees to 70 degrees C if the output of the sensor is 2 mV/1C and the ADC voltage range is 0 to 4 V.

Reference no: EM13229437

Questions Cloud

Explain energetically favourable to promote the electron : following hybridization these 4 unpaired electrons can form covalent bonds. In order to promote an s electron to an empty p orbital, energy is required. Is it energetically favourable to promote this electron when bonding? Why or why not
What are the consequences of these initlaives : what steps have mangers at XeroX taken to effectively manage diversity? what are the consequences of these initlaives?
Why are there so few women an minority ceos of corporations : why are there so few women an minority CEOs of large corporations?
Why was the succession of ursula burns to the top position : why was the succession of ursula burns to the top position at xerox considered historic?
Design the basic interface circuit for a temperature sensor : Design the basic interface circuit (using an op amp) for a temperature sensor that covers a range of 0 degrees to 70 degrees C if the output of the sensor is 2 mV/1C and the ADC voltage range is 0 to 4 V.
Presume all food consumed goes to making atp : One mole of sucrose weighs 342.3 grams. 1mol=6.02*10^23 molecules. Dietary fats (typically 18-20 carbons) contain about 9 dietary calories per gram. Assume all food consumed goes to making ATP
Compute the value of the equilibrium constant : Consider the weathering reaction describing the breakdown of K-feldpar to form the clay mineral kaolinite, a reaction of particular importance in tropical soils
Why does effective management diversity make good business : why dose the effective management of diversity make good business senes ?
Explain weak acid potassium hydrogen phthalate : Using the weak acid that you were assigned in this experiment and .100M NaOh, describe exactly (show calculations) how you would prepare 100.0mL of a buffer at pH = 5.50

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Find the surface temperature in f of the computer chip

For computer chip of 10mm (length), 10 mm(width) is operated by power of 0.345 watt, which surrounded by coolant material of temp of 70 F. The Internal energy rate is 3.5J/sec and kinetic energy rate is -4.5J/sec.

  What is an open collector input why is it used on sensors

Draw a strain gauge circuit and its external components to attach to a conveyor mounted only at the ends to measure the load at the center of the conveyor. What type of testing would you need to do to establish a baseline and calibration curve for..

  Explain single phase circuit

Single Phase Circuit, A resistor and a capacitor are connected in series across a 150 V a.c supply. When the frequency is 40 Hz the current is 5 A

  Find the potential difference between the points

The electrostatic potential in space is given by the scalar field V(r)=V(x,y,z)=e^y + (3x)^2-4cos(z) Find the potential difference between the points P(1,1,1) and Q(0,0,0).

  How receiving end maintains a constant load power factor

The SV curve can be used to understand the impact of constant power factor shunt compensation support. In this case, the receiving end is injected with a specific amount of reactive power so that the receiving end maintains a constant load power f..

  What is the rotor pole shift in electrical degrees

a) If the excitation voltage E0 is equal to the terminla voltage ( 4kV ), what is the maximum real power which the motor can deliver without losing synchronism  b) What is the rotor pole shift in electrical degrees, corresponding to the nominal loa..

  Determine the networks equivalent resistance

A network connected between terminals a and b consists of two parallel combinations that are in series. The first parallel combination is composed of a 10-phm resistor and a 15-ohm resistor. The second parallel combination is composed.

  What is the maximum allowable value of r2

For the amplifier in Fig. P4.20, the maximum value of VS is 2 V and the op-amp can deliver no more than 100 mA. (a) If +-10 V supplies are used, what is the maximum allowable value of R2 (b) Repeat for +-3 V supplies.

  Determine the majority and minority carrier concentrations

A junction employs Nd = 8x 10^17cm^-3 and Na= 2 x 10^ 17 cm^-3. The device is at 300K. (a) determine the majority and minority carrier concentrations on both sides (b) Calculate the built-in potential at (i)T=250K (ii)300K

  Find the error for a 1 degree c change in temperature

A pressure measurement system is stated as having the following characteristics. Range: 0 to 140 kPa; Accuracy: ±1.5% of the displayed reading; Temperature sensitivity: ±0.1% of the reading per °C If the instrument indicates a pressure of 120 kPa

  How to evaluate power dissipated in the components

how to evaluate power dissipated in the components of an RLC series circuit by using matlab software?

  Determine the phase relation between vo and ig

Determine the phase relation between V o and i g for the given network if V g = 45sin(317t) and determine v o for the given network

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd