Design of a condensing system for steam

Assignment Help Mechanical Engineering
Reference no: EM13946414

1. Two configurations are being considered in the design of a condensing system for steam at 1 atm employing a vertical plate maintained at 90°C. The first configuration is a single vertical plate and the second consists of two vertical plates (L/2) X w, where and are the vertical and horizontal dimen- sions, respectively. Which configuration would you choose?

2. The condenser of a steam power plant consists of a square (in-line) array of 625 tubes, each of 25-mm diameter. Consider conditions for which saturated steam at 0.105 bars condenses on the outer surface of each tube, while a tube wall temperature of 17°C is maintained by the flow of cooling water through the tubes. What is the rate of heat transfer to the water per unit length of the tube array? What is the correspond- ing condensation rate?

Reference no: EM13946414

Questions Cloud

Motor stationary, voltage drop in the armature winding : Calculate the efficiency of a 500V shunt motor when taking 700A from the following data taken when the motor was hot: motor stationary, voltage drop in the armature winding 15V.
Total condensation rate and heat transfer rate : Determine the total condensation rate and heat transfer rate for the process of Problem 10.46 when the pipe is oriented at angles of () = 0, 30, 45, and 60° from the horizontal.
What''s the significance of the programming language : What are you going to recommend and why - again with reference to his remarks
What is the probability that the chip ultimately drawn from : Urn I contains three red chips and one white chip. Urn II contains two red chips and two white chips. One chip is drawn from each urn and transferred to the other urn. Then a chip is drawn from the first urn. What is the probability that the chip ult..
Design of a condensing system for steam : 1. Two configurations are being considered in the design of a condensing system for steam at 1 atm employing a vertical plate maintained at 90°C. The first configuration is a single vertical plate L X w and the second consists of two vertical plate..
The key ethical issues and the stakeholders : Imagine that you are an IT consultant who has been given the task of preparing a report for the management board of a software house that is currently thinking of implementing electronic monitoring throughout its operations.
Saturated steam at atmospheric pressure : A vertical plate 2.5 m high, maintained at a uniform temperature of 54°C, is exposed to saturated steam at atmospheric pressure.
How does shape of the distribution impact what conclude : From the MM207 Student Data Set identify one variable that is discrete and one variable that is continuous. Explain your reasoning. How do you know?
What are the good/bad choices the first two rdb systems made : What is the key benefit provided by the relational model over previous data models?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Mass flow rate of air through all devices is 80 kgs show

a gas power cycle compresses air at 1 bar and 300 k state 1 through an adiabatic reversible compressor to 6 bar state

  Compute all the stationary spot price equilibria

Compute all the stationary spot price equilibria, (x0 , x1, P , r , G, T), in which P = r = 1.

  Steam is now heated until its volume is 5m3 and its

steam at 75kpa and 13 percent quality is contained in a spring loaded piston-cylinder device with an initial volume of

  Find the maximum thermal efficiency of this heat engine

you have a heat engine that has a thermal energy resevoir available at 500c the thermal energy to heat the engine is at

  Calculate the pressure and temperature at the remaining

an engine operates on an ideal cold air-standard otto cycle with a compression ratio of 8 r v1v2. heat transfer to the

  Determine what this fda is an approximation of the order of

consider the following finite difference approximation for the base point xi in a one-dimensional finite difference

  What is the azeotrope pressure and composition

In the system A + B activity coefficients can be expressed by the one-parameter Margules equation with A=0.5. The vapor pressures of A and B at T=80C are 900mmHg and 600mmHg respectively. Is there an azeotrope in this system at T=80C and if so, what ..

  For each process of a closed system show the initial and

for each process of a closed system show the initial and final states on a properly-labeled t-s diagram evaluate the

  Determine how long it will take for the system to rise 10 m

an elevator is created by using a hose hanging from the top of a 10 m building. the hose is diverted into 4 jets at the

  Determine the static head efficiency required of the

in an automotive gas turbine the centrifugal compressor is driven at 40000 rpm by an axial turbine. the compressor

  Matlab program-average of digits of part using for loops

Write the MATLAB program to find the maximum, minimum and average of the digits of part (a) using for loops. Execute the program and list the output. Note that you are not allowed to use MATLAB commands max(x), min(x) and mean(x), except for checking..

  What is heat transfer rate from air into the cooling coil

An air conditioning unit has two inlet air streams: a stream of return air from the building (2.25 kgs at 25C) and a steam of outside air (0.75 kg/s at 30 C). These streams are blended and then colled by a cooling coil to 20 C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd