Design circuit that takes sinusoidal input of varying freq

Assignment Help Electrical Engineering
Reference no: EM13251110

Design a circuit that takes a sinusoidal input of varying frequency at 1V amplitude and produces an output amplitude of approximately 1V when the frequency is 1 Hz and approximately 0.5V when the frequency is 1,000Hz. Choose real component values to get as close as possible to the specified amplitudes.

Reference no: EM13251110

Questions Cloud

How much power would that be on the average : A common energy consumption for a family is about 1000 kW hr / month. How much power would that be on the average. (Hint: Notice that hour and month are both units of time so kW hr per month is really a power unit.
Explain the highest-energy subshell at the top : Show the orbital-filling diagram for S (sulfur). Stack the subshells in order of energy, with the lowest-energy subshell at the bottom and the highest-energy subshell at the top.
How deep is the pool : A 4.6m -wide swimming pool is filled to the top. The bottom of the pool becomes completely shaded in the afternoon when the sun is 20?above the horizon, How deep is the pool
Find out the ph of the solution at that point : Most of the solid did not dissolve because the Ksp of ferric hydroxide is very small at 3 x 10^-39. However, when a certain amount of strong acid was added, the entire amount of solid dissolved. Determine the pH of the solution at that point that ..
Design circuit that takes sinusoidal input of varying freq : Design a circuit that takes a sinusoidal input of varying frequency at 1V amplitude and produces an output amplitude of approximately 1V when the frequency is 1 Hz and approximately 0.5V when the frequency is 1,000Hz.
What should be your primary goal in a team and why : You will be part of a team creating a research project. How will you use your understanding of the stages of team development to improve your team's effectiveness? (2-3 Paragraphs)
Explain what energy does the electron move : An electron in the n2= 5 level of an H atom emits a photon of wavelength 1282.17 nm. To what energy does the electron move. Is the photon in the visible region
Calculate the sag in a 90-yard span of a overhead line : Calculate the sag in a 90-yard span of a 0.035 -in^2 overhead line when covered with ice to a radial thickness of 5/8 in, in a wind that exerts a pressure of 9 lb/ft^2, assume the breaking load as 1620 lb and the weight of the conductor as 0.1 lb/..
Examine and evaluate a specific organizations behavior : To examine and evaluate a specific organization's behavior from an ethical and social responsibility view point

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the compensator pole of utility feedback system

A unity feedback control systems for a robot submarine has a plant with a third-order transfer function G(s) = K / (s(s + 10)(s +50)) We want the overshoot to be approximately 7.5% for a step input

  Calculate the value of the voltmeter resistor-rv

A simple voltmeter with a full-scale reading of 50(V) is required. Use a d'Arsonval movement with a rating of 20(mV) at 1 (mA). Calculate the value of the voltmeter resistor, Rv, required to achieve these design specifications.

  Explain what are the distinguishing features of the response

What are the distinguishing features of the response in the pass-band? What are the distinguishing features of the response in the stop-band? What is an all pass filter?

  Find the equivalent impedance for z1

Find the equivalent impedance for Z1 = 60 L+60 and Z2 = 80 L-45 when these are connected in parallel What are the branch currents and the total circuit current if the supply voltage to the circuit is VS = 240V L0

  Explain what is the db bandwidth of the amplifier

A 1 kHz sine wave signal with a power level -10 dBm is applied to the input of the amplifier. What is the power at the amplifier output in dBW?

  Why does the mobile carrier concentration increases

b) What are the equilibrium electron and hole concentrations at 300K and 500K (hint: You will have to find Nc and Nv at 500K, but it isnt necessary for 300K) c) Why does the mobile carrier concentration increase at high temperatures

  What is the value the minimal input signal variation

Analog to Digital Converters The input signals of an (10bits) ADC are from -1Volt to +1Volt. a) What is the rage of the converters b) What is the resolution c) What is the precision What is the value the minimal input signal variation that this ADC c..

  Design an xor gate using standard cmos logic

Design an XOR gate using standard CMOS logic and with pass-transisitor logic and determine the number of transistors (NMOS and PMOS) required for each implementation.

  What is the output snr of matched filter

if Eb the energy per bit of a binary digital signal, is 10^-5 watt-sec and the one sided power spectral density of the white noise ,N0= 10^-6w/hz then what is the o/p SNR of matched filter.

  Calculate the voltage across 480 v winding

A single phase two winding transformer having rating: 20 KVA,480/120 V, 60 Hz A source connected to the 480 V winding supplies an impedance load connected to 120 V winding. The load absorbs 15 KVA at 0.8 pf lagging when load voltage is118 V.

  Find the system transfer function of the system

Find the system transfer function H(s) = Y(s)/X(s) if the input x(t) and the output y(t) of the system are related by the equation y(t) + 3y(t) = x(t) - x(tau)d tau. Assume y(0) = 0.

  Describe the operation of the series rc circuit

Describe the operation of the series RC circuit. The discussion must address phase angle relationships of current and voltage. The answer must include the effect of source frequency on the voltage drops across the resistor and the capacitor at ver..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd