User Account

All Pages

Design & analysis of air conditioning system

Assignment Help Mechanical Engineering
Reference no: EM131092572 , Length: 4500 words

Design & analysis of air conditioning system for heavy vehicles using their exhaust 

Heat 

Introduction

Project preview:-

·         Evaporator

·         Compressor

·         Condenser

·         Receiver

·         Expansion valve

·         Refrigerant:-

·         Which of these components consume the maximum energy from the engine?

Project inspiration:

·         Source of inspiration

·         Vapour  absorption refrigeration system   (vars)

·         What is absorption?

Field of work

Rationale & scope of the project

Objective & hypothesis of the project

Complete work plan

Retrieval of material

Fabrication 

Reference no: EM131092572

Questions Cloud

Identifying market segments and targets : Identifying Market Segments and Targets-At this writing, Bombardier is in the very late stages of bringing to market its new series of mid-sized, cost- and fuel-efficient line of C Series commercial airliners
Health hazards associated with exposures : As you prepare your paper, keep in mind that this should be a high-level overview that is understandable to all employees in the organization: from upper management to production workers. All sources used, including your textbook, should be cited ..
Marketing plan to sell booze at starbucks : Marketing Plan to sell "Booze" at Starbucks. Is this even something you can do or is there parts of the work you can do
Explain any variants of the vulnerability : Explain whether/how you think this type of vulnerability may be modified or extended in future, and identify possible directions for improving detection and/or mitigation of similar vulnerabilities in future systems.
Design & analysis of air conditioning system : Design & analysis of air conditioning system for heavy vehicles using their exhaust
Harvard style referencing required : A. Using relevant HRM theoretical frameworks, describe the core HR activities (as indicated below) s implemented in your organization and evaluate their effectiveness.
Cultural variables in the communication process : What are the cultural variables in the communication process and what are the different types of nonverbal communication?
Discuss errors in perception and selection : Write a 2000 words on Untrained interviewers can make mistakes that are very costly to the organization.” Discuss errors in perception and selection that interviewers can make and how to avoid them.
Detail the steps in a secret ballot representation election : 1. Identify and discuss in detail the steps in a secret ballot representation election. Who initiates this process? Explain.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Emissivity of the pipe surface

A steam pipe 200 mm in diameter passes through a large basement room. The temperature of the pipe wall is 500°C, while that of the ambient air in the room is 20°C. Determine the heat transfer rate by convection and radiation per unit length of ste..

  A steel tensile specimen with starting gage length 20 in

a steel tensile specimen with starting gage length 2.0 in and cross-sectional area 0.5 in2 reaches a maximum load of

  Determine the rate of heat transfer to the rods in the oven

Long cylindrical steel rods (p=7833kg/m3 and cp=0.465kJ/kg*°C) of 8-cm diameter are heat treated by drawing them at a velocity of 4m/min through an 8-m-long oven maintained at 900°C. If the rods enter the oven at 25°C and leave at 750°C,

  A value that causes the 24 hr average velocity to be 20 ms

a wind turbine with a swept area of 1000 m2 operates with 56 efficiency under stp conditions. at the location of the

  Calculate the critical heat flux on a large horizontal

1. Calculate the critical heat flux on a large horizontal sur- face for the following fluids at 1 atm: mercury, ethanol, and refrigerant R-134a. Compare these results to the critical heat flux for water at 1 atm.

  Do need to be concerned about the thermal contact resistance

A wall consists of two layers of insulation pressed  against each other. Do we need to be concerned about the thermal contact resistance at the interface in a heat transfer analysis or can we just ignore it?

  Tubular body for high-pressure coolant and a carbide tip

What drill has one set of flutes that are ground to more than one diameter? What drill category includes more than one set of flutes allowing multiple diameters? What drill type incorporates a tubular body for high-pressure coolant and a carbide tip?

  Estimate the average peak friction angle

Assuming the dry unit weight of sand to be 16 kN/m3, estimate the average peak friction angle, f 9, of the sand. Use Eq. (3.53).

  Coefficient of kinetic friction between the wheels and road

A 3500 Ib. automobile is traveling down a 10 incline a 20 ft/./s. if the driver slams the break, causing the wheels to lock , determine how far the tires slide. the coefficient of kinetic friction between the wheels and the road is uk=0.5

  Your family grows over time and the required water supply

suppose you build a rural house where you need to run a pipe to the nearest water supply which fortunately is about 1

  Water is being filled with water through two inlet pipes

A tank initially filled with 500 lb liquid water is being filled with water through two inlet pipes. One delivers hot water at mass flow rate of 1.5 lb/min and the second delivers cold water at a mass flow rate of 3 lb/min. A single exit pipe is drai..

  Pressures-temperatures and specific volumes around the cycle

A cycle composed of three processes: poly tropic compression (n=1.5) from 137 kPa and 38 degrees C to state 2, constant pressure from state 2 to state 3 and constant volume from state 3 to state 1. The heat rejected is 1560kj/kg and the substance is ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd