Design an interface for the geared dc motor

Assignment Help Electrical Engineering
Reference no: EM13254285

1. Design an interface for a ±24 V, 500 mA geared DC motor. The time constant of the motor is 10 ms. Include software to adjust the delivered power from 0 to 100%.

2. An alarm is powered by 120 VAC, and the on/off state of the alarm is controlled by an EM relay. Design the interface between a computer output port and the EM relay. The dropout voltage is 3.5 V, and the coil current needs at least 100 mA. Limit the coil voltage to 6 V. Write three software functions: Alarm_Init, Alarm_On, and Alarm_Off.

Reference no: EM13254285

Questions Cloud

Identify the key writing and editing strategies : Identify the key writing and editing strategies you applied when completing your research essay. Discuss any obstacles or challenges you had revising and editing your paper.
Find relationship between length of wire and magnetic field : What is the relationship between the length of a wire and magnetic force, Is the relationship between current and magnetic force linear
Later buddhist notions of enlightenment : Describe the similarities between Siddhartha’s experience of enlightenment and later Buddhist notions of enlightenment.
Seller selection being vital to the success of a project : With proper seller selection being vital to the success of a project, all of the below would be considered good selection criteria for a buyer to use to select a seller,
Design an interface for the geared dc motor : An alarm is powered by 120 VAC, and the on/off state of the alarm is controlled by an EM relay. Design the interface between a computer output port and the EM relay. The dropout voltage is 3.5 V, and the coil current needs at least 100 mA.
What is the peak voltage across the capacitor : Consider the RLC series circuit with a 544 ? resistor, a 773 mH inductor (with negligible resistance) and a 810 nF capacitor in series, What is the peak voltage across the capacitor at this frequency
Create a linear programming model for this problem : a company produces two products that are processed on two assembly lines. assembly line 1 has 100 available hours and assembly line 2 has 42 available hours.
How many moles of oxygen molecules would required to react : How many moles of oxygen molecules would be needed to react with 111.2 grams of iron? How many grams of rust would result from this reaction
What is the function describing the standing wave : A standing wave on a 1.70 m long horizontal string displays three loops when the string vibrates at 125 Hz. What is the function describing the standing wave

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Find the losses in the transmission line

A power company supplies 75 kW to an industrial load. The load draws 120 Arms from the transmission line. If the load voltage is 440 Vrms and the load power factor is 0.8 lagging, find the losses in the transmission line.

  What is the reactive power supplied to the sender

A 100 mile , 300kV, 60Hz transmission line has a reactance of 0.8 ohm per mile and a distributed capacitance of 200,000 ohms per mile. Draw a equivalent circuit phase at the sender end when the receiver is open. What is the reactive power supplied..

  Calculate current in incoming and outgoing transmission line

three single-phase transformers rated at 250kVa, 7200V/600, 50Hz, are connected in wye-delta on a 12470V, 3 phase line, if the load is 450kVA, calculate the current in the incoming and outgoing transmission lines and in the primary and secondary w..

  Explain logic high level

Three two-input "AND" gates have their outputs connected to an "OR" gate. The first "AND" gate has each of its inputs at logic HIGH level. The second "AND" gate has each of it's inputs at logic LOW level.

  Discuss how energy is stored in capacitors and inductors

Discuss how energy is stored in capacitors and inductors. Are the equations linear or non-linear How do you know? Discuss the concept of duality and why it applies to many fundament engineering concepts.

  Calculate the maximum allowable gate drive power

A thyristor is triggered by a pulse of train of 5kHz.The duty ratio of the pulse train are 0.5. If allowable average gate power is 100W, calculate the maximum allowable gate drive power.

  Calculate the total number of kilobytes

in a given byte-addressable computer, memory location 10000Hto 9FFFFH are avaliable for user programs. the first location is 10000H and the last location is 9FFFFH. calculate the following: the total number of bytes available (in decimal)

  Explain what is the primary purpose of a resistor in series

What is the primary purpose of a resistor in series with a LED being driven by a flip-flop?

  Give transient behavior cannot be modeled by having function

Give an example of an RC circuit whose transient behavior cannot be modeled by having a function generator with square wave output replacing the mechanical switch.

  Determine the change in length of edges ab and ad

An 8mm thick brass [E=83 GPa; v = 0.33] plate is subjected to biaxial stress with sigma x = 180 MPa and sigma y = 65 MPa. The plate dimensions are b = 350 mm and h = 175 mm.

  What are the advantages of digital communication over analog

Describe the phenomenon of aliasing caused by under sampling. How can aliasing be mitigated What are the advantages of digital communication over analog What is quantization noise How can you reduce it

  Find rms value of burner current and burner average power

An Electric Range top burner control adjusts the duty cycle of the current and voltage supplied to surface heating element as a function of the control's dial setting. The range controller operates from a 240 VRMS single phase supply

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd