Design a skeet launcher to be mounted

Assignment Help Mechanical Engineering
Reference no: EM131392695

The "Save the Skeet" foundation has requested a more humane skeet launcher be designed. While they have not yet succeeded in passing legislation to prevent the wholesale slaughter of these little devils, they are concerned about the inhumane aspects of the large accelerations imparted to the skeet as it is launched into the sky for the sportsperson to shoot it down. The need is for a skeet launcher that will smoothly accelerate the clay pigeon onto its desired trajectory. Design a skeet launcher to be mounted upon a child "little red wagon." Control your design parameters so as to minimize the shaking forces and torques so that the wagon will remain as nearly stationary as possible during the launch of the clay pigeon.

Reference no: EM131392695

Questions Cloud

Design a fourbar linkage-based pile shaker : Operating speed should be in the vicinity of the natural frequency of the pile-earth system.
Prepare a flowchart that describes the sequence of events : With the stir and heater off, the batch is emptied down to level L2. The whole process then starts again. Prepare a flowchart that describes the sequence of events.
Will you treat the foreign operation as a cost or profit : What measure or measures will you use to evaluate the subsidiary's performance? Will you treat the foreign operation as a cost, profit, or investment center?
Prepare a flowchart that describes the sequence of events : Prepare a flowchart that describes the sequence of events. Be sure to consider any events that could occur in parallel.
Design a skeet launcher to be mounted : Control your design parameters so as to minimize the shaking forces and torques so that the wagon will remain as nearly stationary as possible during the launch of the clay pigeon.
Determine whether ultima company should recognize revenue : Determine whether Ultima Company should recognize revenue from the sale of goods at the time title passes to the customer or whether it should defer revenue recognition until the goods are delivered to the customer.
Prepare a flowchart that describes the sequence of events : With the stir and heater off, the batch is emptied down to level L2. The whole process then starts again. Prepare a flowchart that describes the sequence of events. Be sure to consider any events that could occur in parallel.
Explain why stewardship is an important concept : Explain why stewardship is an important concept. What three traditional functions does accounting fulfill? What types of groups regulate financial accounting statements?
Discuss about individual and institutional discrimination : Describe the difference between individual and institutional discrimination. Then provide a specific example of institutional discrimination (also known as systematic inequality) from current events. Your example may be based on either race or gen..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the smallest horizontal force requirednbspto lift

determine the smallest horizontal force required to lift the 260- crate. the coefficient of static friction at all

  Fnd the ratio of the earths translational ke to its daily

find the ratio of the earths translational k.e to its daily rotational k.e. assume the orbit about the sun is circular

  Assume constant gravitational acceleration

A rocket is launched vertically and reaches its maximum height hmax. What are its velocity, v(t)= (dh/dt) , and height above ground h(t) as a function of time t >_ 0(greater than or equal to) before it lands on ground (h = 0)?

  Considering that the only force on ball is gravity how far

a16 lb bowling ball is rolling with a velocity of 20 fts toward a ramp that is inclined at 20 degrees to the

  The two purposes of amplification for digital systems

The two purposes of amplification for digital systems are (i) to improve signal-to-noise ratio and (ii) to make good use of the dynamic range of the digitizer; in other words, to ensure the best resolution possible.

  Calculate the velocity at the exit of a diffuser when air

calculate the velocity at the exit of a diffuser when air at 100kpa and 20 degree c enters it with a velocity of 500ms

  Find the values of static temperature and static pressure

Determine the change in mass flowrate through the duct associated with the 50% reduction in length. The average friction factor remains constant at a value of 0.03.

  What are the temperature on the left edge of the wall the

a one dimensional wall of material kw10wmk is 50 mm thick with uniform heat generation qlsquolsquolsquo5106wm3. the

  Determine the minimum coefficient of static friction

if the coefficient of static friction between the crate and ground is 0.3 determine the minimum coefficient of static

  Determine the amount of steam generated per unit of fuel

a steam boiler heats liquid water at 200 ordmc to superheated steam at 4 mpa and 400 ordmc. coal fuel from utah which

  Determine the radial wall thickness-speed in rpm

A flat disk of outer radius b-125mm and inner radius a=25mm is shrink-fitted onto a shaft of radius 25.05mm. Both members are made of steel with E=200Gpa, v=0.3, and p=7.8 KN.s2/m4. Determine (a) the speed in rpm at which the interface pressure becom..

  What is the molar mass of the mixture

Inside a rigid container, a mixture of three ideal gases with mass fractions of 30% N2, 50% O2 and 20% CO2 has a total mole of 10 kmol. What's the molar mass of the mixture

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd