Design a 3-bit incrementer-decrementer

Assignment Help Electrical Engineering
Reference no: EM13251290

Design a 3-bit Incrementer/decrementer

use btn_west as incrementer, i.e. when pressed, count increments by 1

use btn_east as decrementer, i.e. when pressed, count decrements by 1

use btn_south as reset, i.e. when pressed the count is resetted to 0.

use LD2, LD1 and LD0 to display count on the board. LD2 being MSB.

When count is 3'b111 and btn_west is pressed, it is reset to 3'b000.

When count is 3'b000 and btn_east is pressed, it is set to 3'b111.

Reference no: EM13251290

Questions Cloud

What is the total added-value created by the players : The buyer (B) has a willingness-to-pay of $200 for the first firm (F1)'s product, and a willingness-to-pay of $250 for the second firm(F2)'s products. What is the total added-value created by the players?
What is the angle between the beams : Two overlapping beams of light of different wavelength ?a = 840 nm and ?b = 460 nm co-propagate through air, What is the angle between the beams travelling through the material
Design a series resonant circuit to have a bandwidth : Design a series resonant circuit to have a bandwidth of 400 Hz using a coil with a Ql of 20 and a resistance of 2 ohm. Find the values of L and C and the cutoff frequencies.
Determine the resistivity of copper : A volltage drop of 0.00039 V is measured across a 1.2 m long piece of copper wire when 10 mA of current passes through it. What is the resistivity of copper
Design a 3-bit incrementer-decrementer : Design a 3-bit Incrementer/decrementer use btn_west as incrementer, i.e. when pressed, count increments by 1 use btn_east as decrementer, i.e. when pressed, count decrements by 1 use btn_south as reset, i.e. when pressed the count is resetted to 0.
Find maximum height does the golf ball achieve after impact : A golf club striking a golf ball imparts a force of2100N over a time of 5.06×10?3s at an angle of 35.0? above the horizontal. What maximum height does the golf ball achieve after impact
Multiple-baseline design differ from a reversal design : What is Goldbergs rationale for the study? Was the study designed to contribute to theory? Do the results of the study contribute to theory and how does a multiple-baseline design differ from a reversal design?
What is this maximum power : The potential difference between the terminals of a battery is 12V when measured directly using a voltmeter. What is this maximum power
What are assumptions used in low-level injection of carriers : The mobility of electrons in certain semiconductor is 1400 cm2/ (volt x sec). At room temperature (T=300K) calculate the diffusion length of electrons. What are the assumptions used in low-level injection of carriers

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Find the complex impedance of the inductance

Find the complex impedance of the inductance. Find the phasor voltage and current, and construct a phasor diagram. Write the current as a function of time. Sketch the voltage and current to scale versus time. State the phase relationship between t..

  What is value of the electric field perpendicular to surface

If an electric field in free space of 57.1 V/m makes an angle of 41 degrees to the surface normal of a dielectric slab with relative permittivity 4.01, what is the value of the electric field perpendicular to the surface just inside the slab

  Explain looking at feedback and some opamp problems

Looking at feedback and some Opamp problems, If the unity gain frequency is 5 MHz and the midband open-loop voltage gain is 200,000, what is the cutoff frequency?

  Determine the frequency and the period of x

a. Determine the frequency and the period of x(t) b. Given another signal, y(t)= sin(3/4(t+1)+3/8), is y(t) identical to x(t) Why c. Given a discrete time signal x[n] = cos(3/4(n+1/2)+1/4) is it periodic Why

  Evaluate required received power that achieves a bit error

Data at a rate of 2 Mbps is to be transmitted via a pass-band communication system whose carrier frequency is 500MHz. A binary antipodal system with roll-off factor of 0.2 is used for this communication.

  Explain how long will the cassette tape player operate

How long will the cassette tape player operate at normal power? A walker's cassette tape player uses 4 AA batteries in series to provide 6V to the player circuit.

  Find the power being absorbed

A current source of 12 cos 2000t A, a 200-ohm resistor, and a 0.2-H inductor are in parallel. Assume steady-state conditions exist. At t = 1 ms, find the power being absorbed by the (a) resistor; (b) inductor; (c) sinusoidal source.

  Find the complex-volt-amperes drawn from the line

A 50 hp, 460 V, three phase induction motor draws 61 amps when operating at rated voltage and at a power factor of 0.85 lagging when supplying a rated load. knowns: 1hp=746watts effeciency (n) = Pout/Pin = Pout/(Pout+losses)

  Determine what area of lawn recieves water

A water sprinkler sprays water over a distance of 30 feet while rotating through an angle of 145 degree . What area of lawn recieves water

  Explain magnitude bode plot for any given transfer function

Magnitude bode plot for any given transfer function Can some one teach me an easy way to make a bode plot for any given transfer function magnitude only (not phase).

  Explain single phase circuit

Single Phase Circuit, A resistor and a capacitor are connected in series across a 150 V a.c supply. When the frequency is 40 Hz the current is 5 A

  Explain what is the framework or reference model

1. There are 4 main classes of network topologies, what are they 2. In communications over a network, protocols are required. What is the framework or reference model that makes this possible

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd