Design 6-input ckt that outputs true when for majority input

Assignment Help Electrical Engineering
Reference no: EM13277909

Assume you have a several "ones-count" circuits that works as follows. A ones count circuit has 3 inputs A,B,C and 2-bit output YZ. YZ is 00 if none of the inputs are 1; YZ is 01 if 1 of the inputs is 1; YZ is 10 if 2 of the inputs are 1; YZ is 11 if 3 of the inputs are 1. Design a 6-input circuit that outputs a true when a majority of its inputs are TRUE by using ones count circuits as builfing blocks. Show how you would interconnect the ones circuit to build a 6-input majority count circuit.

Reference no: EM13277909

Questions Cloud

Determine the mass of ice that melts into water : A 37-kg block of ice at 0° C is sliding on a horizontal surface. The initial speed of the ice is 6.2 m/s, Determine the mass of ice that melts into wate
Write down a recurrence relation and closed form : Write down a **recurrence relation** and the **closed form** for each of the sequences described below. In each case the indices n are natural numbers
Find the maximum average power transfer to the load : The phasor voltage Vab in the circuit is 480 /0° V (rms) when no external load is connected to terminals a,b. When a load having an impedance of 100 j0 Ω is connected across a,b, the value of Vab is 252.9822 /-18.3449° V (rms).
Determine the minimum power rating of this heater : A 0.22-kg coffee mug is made from a material that has a specific heat capacity of 900 J/(kg · C°) and contains 0.23 kg of water. determine the minimum power rating of this heater
Design 6-input ckt that outputs true when for majority input : A ones count circuit has 3 inputs A,B,C and 2-bit output YZ. YZ is 00 if none of the inputs are 1; YZ is 01 if 1 of the inputs is 1; YZ is 10 if 2 of the inputs are 1; YZ is 11 if 3 of the inputs are 1. Design a 6-input circuit that outputs a true
How fast does the water emerge from the hose nozzle : Water flows trough a normal garden hose at 2 m/s. how fast does the water emerge from the hose nozzle
Find the power factor of kva load for lagging power factor : A 65 kVA load with a lagging power factor is combined with a 25 kVA synchronous motor load which operates at pf = 0.60 leading. Find the power factor of the 65 kVA load, if the overall power factor is 0.85 lagging.
Compare the distance he wanted to cover : Compare the distance he wanted to cover in the real world with the "theoretical" distance that could be covered if there was no air resistance - If the engine was close to 100% efficient how much petrol would be used to overcome air resistance duri..
What is the linear speed of the hoops center of mass : What is the linear speed of the hoop's center of mass just as the hoop leaves the incline and rolls onto a horizontal surface

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Eliminate or reduce the ripples caused by ac voltage input

Perform experiments using your circuit design. Using your digital scope, plot (and submit) input voltage and output voltage from your circuit design. Try to vary the filter portion (R, L, C) of your circuit and plot (and submit) output voltages.

  Find the current flow if the time interval between t1 and t2

Given that the number of charges measured at t1 is n1 = 2.20×10^19, and the number of charges measured at t2 is n2 = 7.15×10^19. Find the current flow if the time interval between t1 and t2 is 2 s.

  Use the method of recursion to solve the equations

use the method of recursion to solve the following problems: compute y[n] for n = 0,1.2, when x[n] = 0 for all n andy[-l] = 2. Compute y[n] for n = 0,1.2, when x[n] = u[n]and y[-l] = 0. Compute y[n] for n = 0,1.2, when x[n] = u[n]and y[-l] = 2.

  Find current gain defined as the ratio of the load current

An amplifier with an input impedance of 50 K-ohm, an open circuit voltage gain of 150 V/V, and an output impedance of 100 ? is connected between a 5 K-ohm signal source and a 1 K-ohm load.

  Find the p-n junction led current with doping

An Al0.3Ga0.7As p-n junction LED with doping level ND = 1 x 10^18 cm-3 on n-side and NA=1x10^15 cm-3 on p-side has Vf = 0.9 V forward bias across its junction. The LED cross-section is 200 µm x 200 µm.

  How to use the minimum number of bits to represent the data

One of the biggest challenges with log systems, like the ones used for Intrusion Detection Systems data, is the amount of disk space that they require. For example, storing a message like: "User1 login success", contains 19 characters

  Calculate the mechanical power output and efficiency

The single phase for equivalent circuit parameters for the windings of the motor referred to the stator in (ohms/phase) R1=0.2 R2=0.2 X1=0.3 X2=0.3 .the core losses and the magnetization can be ignored.

  Find value of multiplier resistor to obtain full defection

An AC Voltmeter uses a bridge rectifier and 100 ohm PMMC which requires a 1mA DC current for full-scale deflection. Assuming ideal diodes, calculate the value of the multiplier resistor to obtain full scale deflection with 10 V AC applied to the i..

  What will be the conclusion of each channel cdm system

Consider a 4 channel CDM system with the following CHIPS: A: -1 -1 -1 1 B: -1 -1 1 -1 C: -1 1 -1 -1 D: -1 1 1 1 a) Show that each one of those chips is orthogonal to all of the others. b) If the CDM signal 1 -1 -3 1 is received, by all receivers, ..

  Find change in current as a result of a changing the voltage

Consider a diode biased at 1 mA. Find the change in current as a result of a changing the voltage by (a) -10 mV, (b) -5 mV, (c) +5mV, (d), +10mV. In each case, do the calculations (i) using the small-signal model and (ii) exponential model.

  Calculate the bandwidth of the closed-loop transfer function

In a feedback system, the forward path has a transfer function of the form G(s)=k/(1+s/Omega_p) and the feedback path has a gain of k_fb which is less than unity. Calculate the bandwidth of the closed-loop transfer function

  Determine minimum sampling rate that can be used to sample x

a) Draw a sketch of the spectrum of x(t) = sin3(400πt) Label the frequencies and complex amplitudes of each component. Determine the minimum sampling rate that can be used to sample x(t) without aliasing for any its components.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd