Derive the transfer function of this system with a

Assignment Help Mechanical Engineering
Reference no: EM13614296

For a first order system with a transfer function of (1/(5s+2), given a unit step input, please

a.) Derive the transfer function of this system with a proportional control (Kp) with a feedback loop. Draw the system response for Kp= 1,2,3,...,10.

Draw the body plot of the closed loop system for Kp = 1,2,3,...,10.

b.)Derive the transfer function of the system with a proportional control (Kp) and an integral control (Kt) with a feedback loop. Draw the system response for Kp= 1,2,3,4, and Kt= 0.1,0.3,0.5,1.0.

You may generate four figures each with different Kp and overlaid K1s

Dra the bode plot of the closed loop system for Kp= 1,3; and Kt=0.3,1.0

Reference no: EM13614296

Questions Cloud

A small plastic sphere with a charge of -70 nc is near : a small plastic sphere with a charge of -7.0 nc is near another small plastic sphere with a charge of -12 nc. if the
A series lr circuit includes a 90 v battery a resistance of : a series lr circuit includes a 9.0. v battery a resistance of 0.500 ? and an inductance of 0.800 h. what is the
Lenzs law is said to be a consequence of the principle of : lenzs law is said to be a consequence of the principle of conservation of energy. explain this statement by describing
A car dealer acquires a used car for 14000terms fob : a car dealer acquires a used car for 14000terms fob shipping point. additional costs in obtaining andoffering the car
Derive the transfer function of this system with a : for a first order system with a transfer function of 15s2 given a unit step input pleasea. derive the transfer function
An emf of 10 v is applied to a coil with an inductance of : an emf of 10 v is applied to a coil with an inductance of 40 mh and a resistance of 5.0 ? determine the energy stored
A series lr circuit includes a 90 v battery a resistance of : a series lr circuit includes a 9.0. v battery a resistance of 0.500 ? and an inductance of 0.800 h. what is the
The controller of a school district had recorded the : the controller of a school district had recorded the entireproperty tax levy 20m as revenues when levied during the
In the units of kiloton calculate the kinetic energy of an : some scientists believe that the collision of one or more large asteroids with the earth was responsible for the

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Air enters an adiabatic compressor at 20 degc and 100 kpa

air enters an adiabatic compressor at 20 degc and 100 kpa at a rate of 2 kgs and exits at 700 kpa. if the power input

  A diesel engine performs 2090 j of mechanical work and

a diesel engine performs 2090 j of mechanical work and discards 4125 j of heat each cycle.a how much heat must be

  What is the reason for the system -to increase the air

what is the reason for the system? -to increase the air pressure from 100 to 1200 kpa design uses dual compressors to

  What is the flow rate required to cool and maintain

what is the flow rate required to cool and maintain 0.5 x 0.5 x 0.5 m3 volume of air at 297 K to 199 K, using nitrogen at 199 K

  What was its velocity during this time

what was its velocity during this time? (Hint: Take the origin to be the location of the radar.)

  Assume the water is at constant density as it flows

liquid water enters a manifold series of pipes at 1080 psi and 125 degf with a mass flow rate of 3.5 x 10 6 lb hr and

  What is the pressure at any point at the bottom of the tank

A tank with a flat bottom is filled with water to a height of 3.5 meters. what is the pressure at any point at the bottom of the tank? (You can ignore atmospheric pressure when calculating your answer.)

  Calculate the friction factor and the heat transfer

air at atmospheric pressure and with a mean velocity of 0.5 ms flows inside a thin walled square cross-section duct of

  Calculate the magnitude of the principle stresses the

a steel shaft of radius r75mm is subjected to an axial compression p81kn a twisting moment t15.6kn.m and a bending

  Develop an algebraic expression in the form of an integral

a cross section of a rotating bearing is shown. the spherical member rotates with angular speed omega a small distance

  It is assumed that the wire surface temperature is constant

an electrical wire having a diameter of 1.5 mm and covered with a plastic insulation thickness 2.5 mm is exposed to

  Calculate the velocity v of the collar

Calculate the velocity v of the collar as it hits the stop at B if it is elevated from rest at A by the action of the constant 40-N force in the cord. The cord is guided by the small fixed pulleys.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd