Copper disk is placed in a bath of cooling fluid

Assignment Help Mechanical Engineering
Reference no: EM13710482

In a manufacturing process, a copper disk is placed in a bath of cooling fluid. The copper disk has a 5 cm radius and a 1 cm thickness. The initial temperature of the copper disk is 450 degrees Celsius. The thermal conductivity, density, and specific heat capacity of copper are 400 W/m-K, 8933 kg/m^3, and 385 J/kg-K, respectively. The heat transfer coefficient between the surface of the disk and the cooling fluid is 100 W/m^2-K. Assume that the reservoir of cooling fluid is significantly large such that the temperature of the cooling fluid remains constant.

a) Can lumped capacitance be assumed?

b) If the disk is to be cooled to 200 degrees Celsius in two minutes, what should the temperature of the cooling fluid be?

c) Would a sphere of copper of similar volume cool faster? Explain

Reference no: EM13710482

Questions Cloud

Which step will the ball hit first : A ball rolls of the top of a stairway with a horizontal speed of 2 m/s. The steps are 20 cm high and 16 cm wide. Which step will the ball hit first
Calculate the steady-state displacement of the motor : A lathe can be modelled as an electric motor mounted on a steel table. The table plus the motor has a mass of 50 kg. The rotating parts of the lathe have a mass of 5 kg at a distance 0.1 m from its center. The damping ratio is 0.06 and the natural fr..
What average power is produced by friction as the rock stops : After sliding on a rough, horizontal surface, a 25.0-kg rock initially going 8.5 m/s eventually stops due to friction. What average power is produced by friction as the rock stops
Calculate the work done on the block by the spring : A mass less spring with force constant k = 225 N/m is oriented horizontally and fixed on one end. Calculate the work done on the block by the spring
Copper disk is placed in a bath of cooling fluid : In a manufacturing process, a copper disk is placed in a bath of cooling fluid. The copper disk has a 5 cm radius and a 1 cm thickness. The initial temperature of the copper disk is 450 degrees Celsius. The thermal conductivity, density, and specific..
Find what is its speed after it has traveled : A force in the +x-direction with magnitude F(x) = 18.0 N - (0.530 N/m) x is applied to a 6.00-kg box that is sitting on a frictionless surface. what is its speed after it has traveled
Principal stresses and maximum shear stress : A pressure cylinder (ends closed) having an internal radius of 6 inches and thickness 1 inch is subjected to an internal pressure of 5 ksi, a twisting torque of 50,000 in-lb, and a bending moment of 50,000 in-lb. Determine the principal stresses and ..
Determine for the steam exiting the tank : Three return steam lines in a chemical processing plan enter a collection tank operating at a steady state at 1 bar. Steam enters inlet 1 with flow rate of 0.8 kg/s and a quality of 0.9. Steam enters inlet 2 with flow rate of 2kg/s at 200 degrees C. ..
Find the blocks speed after it has moved : A 6.0-kg block initially at rest is pulled to the right along a frictionless, horizontal surface by a constant horizontal force of 12 N. find the blocks speed after it has moved

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  An air-standard dual cycle has a compression ratio of 9 at

an air-standard dual cycle has a compression ratio of 9. at the beginning of compression p1100kpa t1300k and v114l. the

  Use work and energy to determine the center of mass

bar ab of mass m and mass moment of inertia i 112ml2 is constrained to move within the channel as shown. the bar is

  Calculate the average temperature of the plate surface

Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s over a 1m long flat plate that is heated with a uniform heat flux of 1250 W/m2. Assume the flow is fully turbulent over the length of the plate.

  The vertical component of the landing speed of a parachute

the vertical component of the landing speed of a parachute is to be less than 20 fts. the total weight of the jumper

  Find a suitable generating function

Prove that the transformation Q1 = q12 Q2 = q2 sec p2 p cos p2 - 2q2 P= 1 P2 = sin p2 - 2q1 1 2q1 cos p2 is canonical, by any method you choose . Find a suitable generating function that will lead to this transformation.

  Find the velocity of the bullet and the distance

Find the velocity of the bullet and the distance it has traveled into the water after 4 seconds. Please show detailed step by step process to solution.

  Inner surface of the tube is super hydrophobic

Solve the Navier-Stokes equation for the velocity profile in a thin tube of radius R under a constant pressure gradient dP / dx along its axis. The inner surface of the tube is super hydrophobic, and the slip boundary u(R) = -?(du/dR) should be adopt..

  Heat is required to raise temperature of water to boiling

You are throwing a dinner party and decide to prepare instant Chinese noodles (chicken flavor) for all your guests. From the cooking instruction on the back of the package, you determine that you will need to bring 50 cups of water to a boil for your..

  The isentropic efficiency of the nozzle is 94 determine the

water enters an insulated nozzle operating under steady conditions at a pressure of 60 psia a temperature of 350 degf

  Steam enters a turbine at a pressure of 10 bar and

1 steam enters a turbine at a pressure of 10 bar and temperature 360 degree c. it exists the turbine as saturated vapor

  Determine the angle of twist of the end b

determine the angle of twist of the end B of the solid section relative to end C. The tubes have an outer diameter of 30 mm and an inner diameter of 20 mm. The solid section has a diameter of 40 mm.

  Determine the isentropic exit temperature the isentropic

carbon dioxide enters an adiabatic compressor at 100 kpa and 300 k actual inlet conditions at a rate of 0.5 kgs and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd