Convert the composition to atomic percent

Assignment Help Mechanical Engineering
Reference no: EM13708190

A copper and nickel alloy has the following composition: 80wt% Cu and 20wt% Ni. Convert the composition to atomic percent.

Reference no: EM13708190

Previous Q& A

  Derive the material balance equation

Derive the material balance equation for a tank with rigid and incompressible fluids for the following conditions...The tank is initially full of oil at Pi some oil is bled off to reduce the pressure to P1 the oil removed from the tank is collected a..

  Determine the power required for steady speeds

Extensive testing of an experimental 2820-lb automobile reveals the aerodynamic drag force FD and the total no aerodynamic rolling-resistance force FR to be as shown in the plot. Determine (a) the power required for steady speeds of 22 and 44 mi/hr o..

  Calculate the density of the air in the round section

At one section in an air distribution system, air at 14.7 psi and 100degree F has a velocity of 1200 ft/min a and the duct is 12 in x12 in square. At another section the duct is round with a diameter of 18 inches and the velocity is 900 ft/min. Calcu..

  Determine the specific volume of the rock

A rock weighs 90.8 N in air and 45 N when completely submerged in water. Determine the specific volume of the rock in m3/kg

  A turbine extracts energy from water flowing through

A turbine extracts energy from water flowing through a 11-cm-diameter pipe at a pressure of 700 kPa with an average velocity of 11 m/s. If the turbine is 90 percent efficient, how much energy can be produced if the water is emitted from the turbine t..

  Determine the temperature of the air and the initial volume

1750g of air performs an expansion work of 3100kJ on the surrounding as it expands isothermally to a pressure of 63000kPa ad a volume of 0.065 cubic meters. Determine the temperature of the air and the initial volume.

  Undergoes a reversible adiabatic process

In a polytropic process, a fluid is compressed to 2.75 times its initial pressure, whereas its temperature becomes1.65 times. What is the fluids index of expansion, n? 1.2kg of Air at a pressure of 2.15MPa and a temperature of 585K, undergoes a rever..

  Determine the mass of the air-initial temperature of the air

Air exerts a pressure of 900KPa within a 0.45 cubic meter container of fixed volume. It is cooled such that the pressure falls to 3.25bar. The temperature of the air is then measured and was found to be 285C. Determine the mass of the air, the initia..

  Determine power developed by the turbine

Air enters a gas turbine with a velocity of 165m/s and a specific enthalphy of 2800KJ/kg and leaves with a velocity of 135m/s and specific enthalpy of 2175KJ/kg. The heat lost to the surrounding turbine is 32.5KJ/kg. Determine power developed by the ..

  Fundamentals of fluid mechanics

Liquid water in a pumped flow system experiences varying pressures as it circulates through the system. One concern in designing any such system is to ensure that cavitation does not occur. If the water temperature during operation of a particular sy..

Reviews

Write a Review

 

Similar Q& A

  What is the difference between mixed and unmixed flow

What is the difference between mixed and unmixed flow in heat exchangers?

  Measurements of the load required to propagate a crack

SEM212 - Aim of this demonstration is to use measurements of the load required to propagate a crack (tear) in packaging tape to determine its fracture toughness.

  Determine the distance it travels before it starts

determine the time it takes for the ball to start rolling without slip and its speed when it does so. In addition, determine the distance it travels before it starts rolling without slip. Assume (mu)K = 0.10.

  How would you describe the state of the water in a

how would you describe the state of the water in a bathtube? how would you describe the process that this water

  Dtermine a the pressure at the exit in bar and b the work

air at 1600 k 30 bar enters a turbine operating at steady state and expands adiabatically to the exit where the

  The length of a cast iron pipe is to be 4200 ft the head

the length of a cast iron pipe is to be 4200 ft. the head causing flow is to be 12.6 ft. after the pipe has been in

  Graphically determine the angular rotation required to

sketch the ewald sphere construction for the 200 diffraction with mo kalpha radiation and a poly crystalline specimen

  Metal cannot experience any plastic deformation

A metal cylinder metal cylinder 120.0mm long and 15 mm in diameter is to have a tensile force of 15000N applied. Which of alluvium, copper, brass, nickel steel and titanium are good options if the metal cannot experience any plastic deformation?

  Refrigerant 134a undergoes a constant pressure process from

refrigerant 134a undergoes a constant pressure process from saturated vapor at -18.8degc to a final temperature of

  Determine a the time required for the train to travel the

a commuter train traveling at 40 mi h is 3 mi from a station. the train then decelerates so that its speed is 20 mi h

  Assuming ideal-gas behavior for air steady flow and

air enters a compressor at 105 kpa and 300 k with a volumetric flow rate of 12 m3min and exits at 1200 kpa and 400 k.

  Find the sum of two harmonic motions of equal amplitude but

find the sum of two harmonic motions of equal amplitude but of slightly different frequencies. discuss the beating

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd