Constuct a choice table for interest rate from 0% to 100%

Assignment Help Civil Engineering
Reference no: EM13557086

The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the analysis. he has assembled the following data

alternative total investment total net annual revenue

sell parking lot 0 0

keep parking lot 200,000 22,000

build 1 story building 400,000 60,000

build 2 story building 555,000 72,000

build 3 story building 750,000 100,000

build 4 story building 875,500 105,000

build 5 story building 1,000,000 120,000

the analysis period is be 15 years. for all alternatives, the property has an estimated resale(salvage) value at the end of 15 years equal to the present total investement.

(a) constuct a choice table for interest rate from 0% to 100%

(b)if the MARRR is 10%, what recommendation should bill make?

Reference no: EM13557086

Questions Cloud

Determine the force p in the coupling between the trailer an : The hydraulic braking system for the truck and trailer is set to produce equal braking forces for the two units. If the brakes are applied uniformly for 5 sec to bring the rig to a stop from a speed of 20 mph while moving down a 10 percent grade
Determine the rate of heat exchange between the human : A human with a surface area of 2 m^2 and a surface temperature of 27 degrees celcius radiates into a large room (which acts as a black body),
What is the exit state of the water : Water flows through a tube at a rate of 7.5 kg/min while heat is added to it at a rate of 4.5 kW. If water entered at 20 degrees celcius, determine the exit temperature. Assume the pressure remains constant at 1 atm throughout.
Estimate the standard deviation of the population : A sample of 10 television tubes produced by a company showed a mean lifetime of 1200 hours and a standard deviation of 100 hours. Estimate
Constuct a choice table for interest rate from 0% to 100% : The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the a..
What maximum force can this person apply with this jack : A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour. (Assume the specific gravity of petrol is 0.720 and g is ..
What is its speed at the point that the force resisting : This problem models an insertion process. Block A (mA = 2kg) is acted on by a horizontal force F (F = 12 N). As A moves to the right, it gets pressed more and more tightly in the channel.
How long will it take for the pce to reach the well : The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)
How long will it take the water in the aquifer to travel : A truck spils 1 gallon of benzene into an aquifer with an area= 50ft^2 Benzene has a solubility of 1750 ppm, and a specific gravity of 0.873. The aquifer ahs a porosity of 0.25, a hydraulic gradient of 0.004 and a hydraulic conductivity of 1000 gpd/f..

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What would the concentrationin the effuent be 7 days later

A lagoon with a volume of 1200 m^3 has been receiving a steady flow of a conservative waste at a rate of 100m^3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10mg/L.

  Industrial history repeats itself

There are many parallels between the industrialization of the United States after Reconstruction and the modernization of the American workforce in the last twenty to thirty (20-30) years as it transitions from industry to a service-oriented econo..

  Question 1 what is the difference between labor cost and

question 1. what is the difference between labor cost and labor pro-ductivity? use a sketch to illustrate.question 2.

  Determine how to find the maximum moment for the beam

For a 30ft simply supported beam, there is a uniform load of 1.5 k/ft. along the length and two point loads of 20 kips each spaced at (from x=0 to x=30ft left to right) x=10ft and x= 20 ft.

  Calculate depth downstream of jump and energy loss in jump

A hydraulic jump occurs in an rectangular channel 2.3 m wide when the discharge is 2.5 m^3/s. If the upstream depth is 0.25 m calculate the depth downstream of the jump and the energy loss in the jump.

  What is the magneticflux through each turn of the coil

An emf of 22.0 mV is induced in a495 turn coil when the current is changingat a rate of 5.0 A/s. What is the magneticflux through each turn of the coil at an instant when the currentis 1.00 A

  Determine length of an interval of time for atleast one call

determine the length of an interval of time such that the probability of at least one call in the interval is 0.90

  Compute the flows with return periods of 1 5 and 15 years

The table below provides the flows for the Llano River in Texas for the period of 1951 to 1970. Using the simplified frequency analysis method show in class (Weibul method)

  Determine the discharge of a trapezoidal concrete channel

Determine the discharge of a trapezoidal concrete channel section with a bottom width of 4 ft and side slopes of 2:1. The depth of flow is 5 ft and the channel slope is 0.5%

  Calculate the flow depth y3 of the sluice gate

A rectangular channel carries discharge of 10 m^2/s per unit width, with a sluice gate. Calculate the flow depth y3, if a hydraulic jump forms downstream of the sluice gate when y1 = 20 m.

  What is the max length to which it may be stretched

For an unknown alloy the stress at which plastic deformation begins is 400MPa and the modulus of elasticity is 120GPa. If the original specimen length is 76 mm, what is the max length to which it may be stretched without causing plastic deformatio..

  What is the dry unit weight the saturated unit weight

What is the dry unit weight, the saturated unit weight, and the buoyant unit weight, of a soil having a ratio of 0.5 and a value of Gs of 2.7

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd