Consider the variation of specific heat with temperature

Assignment Help Mechanical Engineering
Reference no: EM13710341

A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 7.

Determine the back work ratio of this cycle, if the temperature of air at the compressor and the turbine inlet are 300 K and 1300 K respectively. (Consider the variation of specific heat with temperature)

Reference no: EM13710341

Questions Cloud

Review or appraisal based on careful analytical evaluation : Your analysis should explore the positives and negatives in each case and reach a balanced view of the strengths and weaknesses of the person you have selected.
Hot water is provided to a house by electric water heater : Hot water is provided to a house by an electric water heater which uses a 60L tank. The electric heater is rated for a 1.6kW. The hot water tank is completely full with water at 80°C when someone starts a shower. The shower faucet mixes cold water at..
What is the annual after-tax cost of debt : What is the annual after-tax cost of debt to the company on this issue and how much must the assets be reduced to bring the TATO to the industry average - what is the project's IRR?
What is final temperature and assume process is adiabatic : An evacuated 1-ft3 tank is connected by a valve to a nitrogen supply line flowing air at 120 psi and70oF. A valve is opened allowing air to flow into the tank until the pressure reaches 90 psi. How much mass flowed into the tank and what is its final..
Consider the variation of specific heat with temperature : A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 7. Determine the back work ratio of this cycle, if the temperature of air at the compressor and the turbine inlet are 300 K and 1300 K respectively. (Consider the v..
Determine the radius of curvature of the particle path : A particle which movies in a two-dimensional curvilinear motion has coordinates in millimetres which vary with time t in seconds according to x=5t2 +4 and y=2t3 + 6. For time t =3s, determine the radius of curvature of the particle path and the magni..
Neglect kinetic-potential energy changes-compressor power : Air is compressed at steady state from 100 kPa, 300 K, to 600 kPa, 440 K with a mass flow rate of 4 kg/s. Heat transfer occurs at a rate of 42.3 kJ/kg of air flowing to cooling water circulating in a water jacket enclosing the compressor.
What is the mass flow rate of gaseous oxygen : Liquid oxygen (LOX) is used as rocket fuel to launch satellites into space. However, it is easier (and less dangerous) to transport oxygen in gaseous form. What is the mass flow rate of gaseous oxygen that flows at 25 m/s through a 0.5-meter diameter..
Neglecting heat transfer and potential energy : Steam enters a nozzle at steady state at 20 bar and 280°C, with a velocity of 80 m/s. The exit pressure and temperature are 7 bar and 180°C. Mass flow rate is 1.5 kg/s. Neglecting heat transfer and potential energy. Sketch the process on a T-v diagra..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A hot air ballon is traveling upward at a velocity of 1094

a hot air ballon is traveling upward at a velocity of 10.94 fts and at a horizontal velocity of 18.23 fts. if sand bag

  The automatic transmission in a car receives 25 kw shaft

the automatic transmission in a car receives 25 kw shaft work and gives out 24 kw to the drive shaft. the balance is

  Calculate the rate of heat transfer per unit surface area

calculate the rate of heat transfer per unit surface area by radiation between two brick walls a short distance a part

  What is the limitation on the thickness of specimens for a

1how do the rockwell and brinell tests actually measure hardness ? give any appropriate sketches and formula. are there

  Two resistors r1 1200 ohms and r2 2000 ohms are connected

two resistors r1 120.0 ohms and r2 200.0 ohms are connected in parallel to each other then in series to a 12.0 volt

  A variable force and appropriate energy transfers are

ten kilograms of water initially at 3000 kpa 200degc are contained in a piston-cylindernbspdevice shown below. a

  Fluidized bed boiler system by making the most appropriate

500 mw of thermal capacity and t 450 deg c p 80 bar boilers of thermal power plant in 6000 a valuable and

  If a heat pump is used to pump heat from the outside to the

it is found that 10 btus of heat must be supplied to a house in order to maintain its temperature at 70of when the

  Compute the magnitude of the load

on the basis of the information given ,is it possiple to compute the magnitude of the load that is necessary to produce this change in length?

  Determine the rate at which energy is removed by heat

the refrigerator steadily receives a power input of .15kw while rejecting energy by heat transfer to the surroundings

  Refrigerant enters the condenser of residential heat pump

Refrigerant-134a enters the condenser of a residential heat pump at 900 kPa and 40°C at a rate of 0.02 kg/s and leaves at 900 kPa as a saturated liquid. If the compressor consumes 1.2kW of power, determine (a) the COP of the heat pump and (b) the rat..

  Define mach number and determine the type of speed an

define mach number and determine the type of speed an aircraft is flying if the aircraft speed is 880 mph at an

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd