Consider adiabatic mixing chamber operating at steady state

Assignment Help Mechanical Engineering
Reference no: EM13719317

Consider an adiabatic mixing chamber operating at steady state into which steam enters with quality of 0.9. Water enters through a separate inlet at 300C. At the exit the temperature is 1500C and mass flow rate is 2 kg/s. The pressure in the mixing chamber is 800 kPa. Determine the entropy production for the mixing process, in kW/K.

Reference no: EM13719317

Questions Cloud

Business organization form choice memorandum instructions : For this assignment you will draft a memorandum to your instructor (pretending that your instructor is the lawyer in a law firm where you are working as a paralegal) answering the following questions for your business that you discussed in ..
An enterprise which has a long connection with d&g : Jane is employed by D&G Enterprises Ltd as a junior clerk in the mail room. She is sacked because of her inefficiency. On her last day with the enterprise, Jane, using the appropriate order form, orders five hundreds gadgets at a cost of $100,..
Calculate the entropy generation rate for the process : Superheated steam enters one section of an open end feed water heater at 5bar and 240 c with a mass flow rate of 1 kg/s. compressed liquid water at the same pressure and 35 C enters another inlet. The mixture of these two streams leaves as a saturate..
Insulated duct of varying cross-sectional area : Air at 300 kPa, 63oC, and a velocity of 423 m/s enters an insulated duct of varying cross-sectional area. The air exits at 150 kPa, 88oC. At the inlet, the cross-sectional area is 6.57 cm^2.
Consider adiabatic mixing chamber operating at steady state : Consider an adiabatic mixing chamber operating at steady state into which steam enters with quality of 0.9. Water enters through a separate inlet at 300C. At the exit the temperature is 1500C and mass flow rate is 2 kg/s. The pressure in the mixing c..
Water initially exists as a saturated liquid : Water initially exists as a saturated liquid at 186oC is contained in a piston-cylinder assembly. The water undergoes a process to the corresponding saturated vapor state, during which the piston moves freely in the cylinder
Assume variable specific heats : Air contained in a rigid, insulated tank fitted with a paddle wheel, initially at 4 bar, 40oC and volume of 0.2 m^3, is stirred until its temperature is 500 K. Assuming the ideal gas model for the air, determine the amount of entropy produced, in kJ/..
Determine the exit temperature of the air : Air enters the evaporator section of an air-conditioner at 100 kPa, 27oC with a volumetric flow rate of 6 m^3/min. R-134a enters the evaporator at 120 kPa with a quality of 0.3 and rate of 2kg/min and it leaves as a saturated vapor at the same pressu..
Heat transfer is negligible are kinetic and potential energy : Steam at 550 lbf/in.2, 70 oF enters a turbine operating at steady state and exits at 1 lbf/in.^2. The turbine produces 500 hp. For the turbine, heat transfer is negligible as are kinetic and potential energy effects.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  How much is the mass rate for the outlet gases that is

1 for the piping diameter changes and flow directions shown below if the velocity at the input is 5 ms the initial

  Linear-syndiotactic polypropylene-cross linked cis-isoprene

For the following pair of polymers, state whether or not it is possible to determine whether one polymer is more likely to crystallize than the other. Linear and syndiotactic polypropylene-Cross linked cis-isoprene

  A 5-ft3 tank contains 06-gravity natural gas at 1500 psia

a 5-ft3 tank contains 0.6-gravity natural gas at 1500 psia and 100of. 200 scf of gas is released from the tank. this

  Aconstant upward acceleration of 0372 fts2 determine the

cylinder b has a velocity of 1.517 fts downward at t0 and a constant upward acceleration of 0.372 fts2. determine the

  Drmine a the temperature of the air at the compressor

the turbocharger of an internal combustion engine consists of a turbine and a compressor. hot exhaust gases flow

  What is the temp of the steam entering the turbine

Steam produced at 70 bar and some unknown temp. A small amount of steam is bled off just before entering a turbine and goes through an adiabatic throttling valve to atmospheric pressure. The temp of the steam exiting the throttling valve is 400C.

  Calculate the number of vacancies at 546degc given that the

the number of vacancies present in some metal at 857degc is 1.7 x 1024 m-3. calculate the number of vacancies at

  Determine the natural convection heat transfer coefficient

experiments have been conducted on a steel vertical flat plate 130 mm in width and 160 mm long. the plate is heated

  The outer ring rotates and the bearing carries a combined

a 60 mm bore 02 series double row angular contact ball bearing has a 15 degrees contact angle. the outer ring rotates

  A single mixed stream exits at 1 bar cpi for air and helium

air at 40oc 1 bar and a volumetric flow rate of 60 m3min enters an insulated control volume operating at steady state

  The hole must have a diameter of b 25 mm determine the

the aluminum plate of thickness t 3.5 mm. is to be designed so the maximum stress remains below 100 mpa. the hole must

  Water at 25 degrees c enters a heat exchanger at 01 kgs and

water at 25 degrees c enters a heat exchanger at 0.1 kgs and exits at 50 degrees c. kerosene enters the other side of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd