Compute the weight percent of niobium

Assignment Help Mechanical Engineering
Reference no: EM13212191

Niobium forms a substitutional solid solution with vanadium. Compute the weight percent of niobium that must be added to vanadium to yield an alloy that contains 1.55 x 1022 Nb atoms per cubic centimeter. The densities of pure Nb and V are 8.57 and 6.10 g/cm3, respectively.

Reference no: EM13212191

Questions Cloud

Design a flat roof meeting certain mechanical performance : Design a flat roof meeting certain mechanical performance criteria. The basic structure of the roof is a series of rectangular-section 'joists', made from softwood, that span the space to be covered by the roof.
What is the rotating speed of the disk in rpm : A slotted disk and opto-interrupter outputs pulses at 62 HZ. The disk has only one slot cut in it. what is the rotating speed of the disk in rpm?
Determine the pressure in the evaporator : Describe IN DETAIL how you could determine the required rate of heat addition or removal.
Explain how will prepare 3-methly-1-butanol : how you will prepare 3-methly-1-butanol from a grignard reagent and any needed aldehyde or ketone.
Compute the weight percent of niobium : Niobium forms a substitutional solid solution with vanadium. Compute the weight percent of niobium that must be added to vanadium to yield an alloy that contains 1.55 x 1022 Nb atoms per cubic centimeter. The densities of pure Nb and V are 8.57 an..
Calculate the velocity v of the collar : Calculate the velocity v of the collar as it hits the stop at B if it is elevated from rest at A by the action of the constant 40-N force in the cord. The cord is guided by the small fixed pulleys.
Explain the solution be acidic and neutral or basic : Consider a 0.53 M solution of each of the following salts in distilled water. Will the solution be acidic, neutral, or basic? You may need to reference a table of Ka and Kb Tables values
Determine the mechanical efficiency of the pump : Water is being pumped from a large lake to a reservoir 30 m above at a rate of 5x10-3 m3/s by a 12 kW (shaft) pump. If the irreversible head loss of the piping system is 8m, determine the mechanical efficiency of the pump.
What is the wear coefficient of the bearing material : What is the wear coefficient of the bearing material in m2N-1 ?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Refrigerant leaves the evaporator as saturated vapor

Refrigerant 134a leaves the evaporator as saturated vapor at 1.4bar and is heated at constant pressure to 20 degrees C before entering the compressor.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Why is the carnot cycle not suitable as an ideal cycle

why is the carnot cycle not suitable as an ideal cycle for all the power producing devices ?

  Determine the latent heat of vaporization of the water vapor

How would you calculate the sensible heat, the latent heat, and determine the latent heat of vaporization of the water vapor in this air stream as the air is cooled from 170 F to 48 F?

  Define aeroplane dynamics

Aeroplane Dynamics, Determine the steady thrust that would enable a 200-tonne airliner to reach its take-off speed (75 m sâ?'1), from rest, in 30 s

  An airfoil of surface area 1ft squared is tested for lift

Lift coefficient (Cl) and lift (L), An airfoil of surface area 1ft squared is tested for lift (L) in a wind tunnel. At an angle of attack of 5 degrees with standard air of density 0.0024 slugs/ft cube at a speed of 100 ft/sec

  Determine the slenderness ratio

determine the slenderness ratio of a 5 m column with built end if its cross section is a circular with a radius of 40 mm and b 50 mm square use the concept of effective length.

  Find the needed length of the heated section

Find the needed length of the heated section of the tube and find the temperature of the water when it exits the heated section of the tube.

  Design a bridge

Design a bridge that will withstand 4 fully loaded semi-trailers

  Computing temperature water evaporation

Calculating temperature, water evaporation, and heat in a power plant cooling situation. In a nuclear power plant the cooling tower system must be run on a closed cycle.

  Explain feasibility

Determining Feasibility, At steady state, a new power cycle is claimed by its inventor to develop 6 horsepower for a heat addition rate of 400 Btu/min

  Find the transfer function for the impulse response

Find the transfer function for the following impulse response

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd