Compute the stress-strain and total elongation

Assignment Help Mechanical Engineering
Reference no: EM13718979

A 24 in long bar with a cross sectional area of 1.0 in^2 is subjected to an axial tensile load of 10,000 lb. compute the stress, strain and the total elongation if the bar material is :

a) steel with E = 30,000,000 psi

b) aluminum with E = 10,000,000 psi

C) Titanuim with E = 16,500,000 psi

Reference no: EM13718979

Questions Cloud

Clockwise without slipping on the fixed horizontal surface : At the instant shown, the rigid body OA rolls counter clockwise without slipping on the fixed horizontal surface, and point O has a velocity 2 m/s to the left and an acceleration of 1 m/s2 to the right. Point O is at the center of the semi-circle reg..
Cauldron of boiling liquid with a pulley system : A witch lifts her cauldron of boiling liquid with a pulley system. Once the cauldron is lifted, liquid issues from two identical holes of cross-sectional area 2,000 mm2 (each) with a velocity of 30 m/s. The liquid sprays 30o below the horizontal.
Energy when completely combusted in air : As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, the car gets an average MPG of 15 MPG. How efficient is the car’s engine during the acceleration assuming 1 gallon ..
Calculate starin in axial and transverse direction : A 10-ft long rectangular ASTM Grade 50 steel plate 1-in by 12-in cross section is used as a hanger and is subjected to a tensile load of 240,000 lb . the modulus of elasticity for steel is 30,000,000 psi and the poison ratio is 0.25
Compute the stress-strain and total elongation : A 24 in long bar with a cross sectional area of 1.0 in^2 is subjected to an axial tensile load of 10,000 lb. compute the stress, strain and the total elongation if the bar material is :
Determine the air velocity at the exit when inlet velocity : The exhaust nozzle of a jet engine expands air at 388 kPa and 174 C adiabatically to 95 kPa. Determine the air velocity at the exit when the inlet velocity is low and the nozzle isentropic efficiency is 96 percent.
Suspended in a room filled with saturated steam : A 1.2-cm-diameter silver sphere initially at 25°C is suspended in a room filled with saturated steam at 100°C. Using the lumped system analysis, determine how long it will take for the temperature of the ball to rise to 50°C. Also, determine the amou..
How long will it take for the surface temperature : A long aluminium cylinder 50cm in diameter is initially at a uniform temperature of 200°C. It is suddenly subjected to a temperature of 70°C and h = 535W/m2K. How long will it take for the surface temperature to reach 100°C.?
Aerodynamics of a new prototype automobile a scale model : To test the aerodynamics of a new prototype automobile a scale model will be tested in a wind tunnel. For dynamic similarity, it will be required to match Reynolds number between model and prototype.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The tube has a inside diameter of 30mm and a bulk t of 20 c

water flows in a long electrical heated tube with q constant . the velocity and temperature profiles are fully

  What is the effect of the propane addition on the mole

a system of propane and n-butane exists in two phase vapor liquid equilibrium at 10 bar and 323 k. the mole fraction

  Determine whether vaporization is a major concern

In coal gasifiers, refractories and metals must withstand the coal/air or coal/oxygen combusting atmospheres. The Zr-Nb-Ti system is under consideration as alternative to the Fe and Ni alloy systems because the coal combustion degrades these alloy sy..

  The power input to the steam is known to be 500 w determine

a refrigeration system is designed to operate between temperture limits of -10 c and 25 c. the power input to the steam

  Poly tropic process in a piston-cylinder assembly

Air undergoes a poly tropic process in a piston-cylinder assembly from P1 = 1 atm, T1 = 70ºF to P2 = 3 atm. Employing the ideal gas model with constant specific heats at 80ºF, determine the work and heat transfer per unit mass, in Btu/lbm, if

  What are the percentages of the total heat absorption

What are the percentages of the total heat absorption taking place in the economizer, boiler drum and the superheater, respectively? Assume cp of air and water as 1.005 kJ/kg K and 4.2 kJ/kg K, respectively.

  Consider the flow of air over a vertical flat plate at a

consider the flow of air over a vertical flat plate at a low velocity u1 in ambient pressure p1. the plate surface

  Find the distance a traveled by the piston if w is the work

a cylinder of cross-sectional area a is divided inot tow chambers 1 and 2 by means of a frictionless piston. the piston

  Constant-area duct is fed by a converging-only nozzle

A constant-area duct is fed by a converging-only nozzle. The nozzle receives air from a large chamber at p1=600 KPa and T1=550 K. The duct has a friction length of 5.3, and it is choked at the exit. What is the pressure at the end of the duct? If 80 ..

  Test results at four different test temperatures

A Charpy V Notch test was conducted for an ASTM A572 grade 50 bridge steel. the average values of the test results at four different test temperatures were found to be

  Calculate the interface pressure at the lx-10 interface

How long in time must the pressure pulse be to allow for a detonation to occur and what is the minimum distance that the shock must traverse to allow for a detonation to occur?

  Calculate delta velocity-semi-major axis for transfer orbit

Calculate the change in velocity required in changing the position of a satellite in an orbit by 90 degrees. The initial and final orbit is circular around the Earth with a 15000 km radius. Calculate the delta velocity, semi-major axis and period for..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd