Compute the sample mean variance and standard deviation and

Assignment Help Civil Engineering
Reference no: EM13559282

an experiment measuring the percent shrinkage on drying of 50 clay specimen produced the following data ;

13.4 17 18.4 20.1 21.2

13.9 17.4 18.5 20.2 21.2

14.2 17.5 18.5 20.3 21.2

14.8 17.6 18.7 20.3 21.2

15.4 17.6 19 20.4 21.4

15.6 17.8 19.3 20.5 22.3

15.8 18 19.4 20.5 23.1

16.4 18.2 19.6 20.6 23.1

16.6 18.2 19.6 20.8 23.6

16.6 18.3 19.7 20.8 24

results mean = 18.95, mode=21.2, median=19, std dev= 2.5 variance =6.27

a) group the data into class interval of size 1% starting with the value 13.0 and draw the resulting histogram.

b)For the grouped data acting as of each of the data point in an interval was actually located at the midppoint of that interval, compute the sample mean,variance and standard deviation and compare with the results above.

Reference no: EM13559282

Questions Cloud

What would the height of a water tower with a 500 gallon : What would the height of a water tower with a 500 gallon tank have to be, to bring water ( by gravity ) from sealevel over a distance of 2.5miles with an elevation of 300ft?
What is the magnitude of the force required at the bottom of : The 1.5m2 pub sign hanging outside The Drunken Engineer, weighs 200N and is hinged along its top edge. Determine the deflection in degrees for horizontal wind speed of 10m/s and what is the magnitude of the force required at the bottom of the sign to..
Find through what distance does the piston drop : Suppose a monatomic ideal gas is contained within a verticalcylinder that is fitted with a movable piston.  find Through what distance does the piston drop
Determine the inside heat transfer coefficient : The specific heat capacity Cp of the process fluid is not known at the mean bulk fluid temperature but is a linear function of temperature, and must be calculated using the following information, Cp at 300K is 1.98 kJ/kgK, and Cp at 400K is 2.65 kJ/k..
Compute the sample mean variance and standard deviation and : For the grouped data acting as of each of the data point in an interval was actually located at the midppoint of that interval, compute the sample mean,variance and standard deviation and compare with the results above.
What would be the concentration of pollutant in the effluent : A lagoon with volume 1,200 m^3 has been receiving a steady flow of a conservative waste at a rate of 100 m^3/day for a long enough time to assume that steady-state conditions apply. the waste entering the lagoon has a concentration of 10 mg/L. Assumi..
What is the maximum tensile stress : A 20-foot long W8X67 is suspended from one end. If the modulus of elasticity is 29,000ksi, determine the following.
Determine the bending moment at the intermediate support due : A beam is simply supported at the ends and is continuous over two spans. The left-hand span is 16 ft and the right-hand span is 20 ft. The beam supports a uniform load of 900 plf, which includes its own weight,
Determine the volume flow rate from the manning equation : Water flows uniformly in a rectangularlined with a glass surface 0.018, channel width is b=10m, the flow depth is y=0.5m ,slope is =0.008 determine the volume flow rate from the manning equation and the critical depth

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate the weight of gas within the blimp for helium

A blimp is approximated by a by a sphere of 25 m in diameter. Estimate the weight of 15°C gas within the blimp for (a) helium at 1.1 atm; and (b) air at 1.0 atm. What might the difference between these two values represent

  What is the anle of internal friction for the sand

A direct shear cell 25.4cm x 25.4 cm in plan is filled with dry sand. a normal load of 6kN is applied to the sample, and the shear failure is 3.5kN. What is the anle of internal friction for the sand?

  Determine what is the oil flowrate in stb per day

Two wells had been drilled on 40-acre spacing. Well 1 is injectionand Well 2 is producing well. Down hole injection pressure is 8500psi, and bottom hole pressure in producing well is 2400 psi.

  Find what is the op amp output voltage with a digital input

The reference current for the DAC0808 is 2.0 mA. With the DAC output connected to the inverting input of an op amp with a feedback resistor of 5.0 kohms, what is the op amp output voltage with a digital input of 0x80

  Determine mass flowrate through boiler needed to produce

Determine the mass flowrate through boiler needed to produce 5000KW of power.

  Types of structures that can be analysed using the package

Search the web or visit a local drawing office to find a commercially available structural analysis package (or one that you are already familiar with). Describe, using your own words, the following features of the package:

  Compute the after-tax rate of return on the vessel

At the end of the 6 years, the oil company exercised its option and bought the vessel. The chemical company has a 34% incremental tax rate. Compute its after-tax rate of return on the vessel.

  What force is necessary to lift a thin 25-mm diameter ring

What force is necessary to lift a thin 25-mm diameter ring out of :

  Question 1as an estimator in a construction firm you have

question 1as an estimator in a construction firm you have been instructed to include only the costs relating to labour

  Find the angle of rotation of the free end of the shaft

The solid compound shaft, made of three di¤erent materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft.

  Determine the tradeoff between the cost and the energy head

Two materials (wrought iron, ks = 0.046 mm, and galvanized iron, ks = 0.15 mm) are being considered for a new pipeline. The expected discharge is 0.15 m3/s. Both the head loss and cost are sought for.

  Determine annual nominal and effective interest rate

If john borrows $6346.40 now to buy a car (the car does not include the down payment) and makes monthly payments of $220 for 36 months beginning one month from now

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd