Compute the flow rate if the final duct size

Assignment Help Mechanical Engineering
Reference no: EM13705986

Hydrogen expands isentropically from 15 bar absolute and 340 k to 3 bar absolute in a steady flow process without heat transfer. 1) compute the final velocity if the initial velocity is negligible B) compute the flow rate if the final duct size is 10 cm in diameter

Reference no: EM13705986

Questions Cloud

Paddle wheel and an electric heater operate in a system : A paddle wheel and an electric heater operate in a system. If the torque is 200 N-m, the rotational speed is 400 rpm, the voltage is 20 V, and the amperage is 10 A, What is the rate of doing work?
Determine the critical load : A steel column has a length of 9 m and it fixed at both ends. If the cross-section area has the dimensions shown determine the critical load. Est = 200 GPa QY = 250 MPa
Carbon dioxide flows in a horizontal duct : Carbon dioxide flows in a horizontal duct at 7 bar abs. and 300 K with a velocity of 20m/s. At a dowstream section, the pressure is 3.5 bar abs and the temperature is 280 K. if 1.4 x 10^4 j/kg of heat is lost by the fluid between these locations.......
Hydrogen flows through a horizontal insulated duct : Hydrogen flows through a horizontal insulated duct. At section1 the enthalpy is 2400 btu/lbm, the density is .5 lbm/ft^3 and the velocity is 500 ft/sec. at at downstream section, h2= 2240 btu/lbm and density2= .1 lbm/ft^3. No shaft work is done. Dete..
Compute the flow rate if the final duct size : Hydrogen expands isentropically from 15 bar absolute and 340 k to 3 bar absolute in a steady flow process without heat transfer. 1) compute the final velocity if the initial velocity is negligible B) compute the flow rate if the final duct size is 10..
Calculate number of vacancies per cubic meter in some metal : Calculate the number of vacancies per cubic meter in some metal at 763°C. The energy for vacancy formation is 0.79 eV/atom, while the density and atomic weight for this metal are 4.77 g/cm3 and 88.45 g/mol, respectively.
Components parallel and perpendicular to the inclined plane : The following figure shows a body on 25 deg inclined plane. The weight of the body represented by the force W is 66lb. resolve this force at point O into components parallel and perpendicular to the inclined plane.
Perfect gas undergoes a reversible polytropic process : A perfect gas (methane) undergoes a reversible polytropic process in which the polytrotic exponent is 1.4. 1) Using the first law, arrive at an expression for heat transfer per unit mass solely as a function of the temperature difference (change in T..
Determine the maximum length of a cylindrical walnut : It is known that a long log floats with its axis horizontal. A very short log, however, floats with its axis vertical. Determine the maximum length of a cylindrical walnut log 30 cm in diameter that will cause it to float with its axis vertical.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the amount of money this facility will save a

during a plant visit it was noticed that a 12-m-long section of a 12-cm-diameter steam pipe is completely exposed to

  The combustion gases leave the heat exchanger at 380 k

the top cycle of a combined cycle power plant has a pressure ratio of 12. air enters the compressor at 300 k at a rate

  Calculate the isentropic work process 1-2s the actual work

air at mass flow rate of 10 kgs at 1 atm 300 k point1 enters an adiabatic compressor and exists at 8 atm 600 k point 2.

  Bron is diffused into highly pure germanium at 1000oc q

boron is diffused into highly pure germanium at 1000oc q 105 kcalmol do 1.1 x 10 m2sec. a steady surface

  Liquid water enters a manifold series of pipes at 1075 psi

liquid water enters a manifold series of pipes at 1075 psi and 125 degf with a mass flow rate of 3.22 x 106 lbmhr and

  Determine a the temperature at the turbine inlet in degrees

a steam turbine at steady state is operated at part load by throttling the steam to a lower pressure before it enters

  Show that this function satisfies the requirements of a

consider the following probability distribution function for a continuous random variablefx 3x6235 -2ltxlt-3

  Estimate the radiant heat transfer from the wire you can

1 a 10-cm long and 20-cm wide circuit board is covered with 100 closely spaced chips each generating heat at a rate of

  Assuming cold air standard assumptions for a spark ignition

assuming cold air standard assumptions for a spark ignition engine cycle otto and given the following data compression

  The turbine exhausts to atmospheric pressure if both the

a gas turbine takes in 250000 lbmhr of air at 80f and compresses it to 6 atmospheres. the combustion of gas adds

  Knowing that at t3 s slider block c has moved 57 mm to the

block b moves downward with a constant velocity of 20 mms at t0 block a moving upward with a constant acceleration and

  10 c at the top and bottom surfaces respectively if the

the concrete slab of a basement is 11 m long 8 m wide and 0.20m thick. during the winter temperatures are nominally 17

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd