Compute how many grams of water must be added to soil

Assignment Help Civil Engineering
Reference no: EM13300696

the natural water of a sample taken from a soil deposit was found to be 11.5%. it has been calculated that the maximum density for the soil will be obtained when the water content reaches 21.5%. Compute how many grams of water must be added to each 1000g of soil( in its natural state) in order to increase the water content 21.5 %.

Reference no: EM13300696

Questions Cloud

How a csr agenda and its related activities are developed : Do you believe that the leadership group of an organisation can have a significant impact on how a CSR agenda and its related activities are developed and implemented?
How much will you have accumulated at the end of 18 years : Assume that you will be able to earn 10%, compounded monthly, on your investment. How much will you have accumulated at the end of 18 years?
Explain what hertz of radiation having energy : Determine the frequency, in hertz, of radiation having energy of 4.08×10?21 J/photon b. Determine the wavelength, in nanometers, of radiation with of 218 kj/mol energy
What equilibrium temperature does the collector reach : A solar collector is placed in direct sunlight where it absorbs energy at the rate of 880 J/s for each square meter of its surface. What equilibrium temperature does the collector reach
Compute how many grams of water must be added to soil : it has been calculated that the maximum density for the soil will be obtained when the water content reaches 21.5%. Compute how many grams of water must be added to each 1000g of soil( in its natural state) in order to increase the water content 2..
Which of categories of owner have limited liability : In terms of organizational costs, which of the following sequences is correct, moving from lowest to highest cost?
Find how much power does the neuron release : The potential difference across a resting neuron in the human body is about 70 mV, How much power does the neuron release
Determine the maximum value of the average normal stress : Knowing that each member has a 2 3 4-in. rectangular cross section and that each pin has a 12 -in. diameter, determine the maximum value of the average normal stress (a) in member BE, (b) in member CF.
How much heat must be supplied to bring it to a boil : A pot containing 1.03 liters of water, initially at 19*C, How much heat must be supplied to bring it to a boil

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Ehermal conductivity of the radioactive wastes

The outer surface of the tank is cooled by air at 300 K with a heat transfer coefficient of 100 W/m2K. Determine the maximum temperature in the tank. Take the thermal conductivity of the wastes as 2.0 W/mK.

  Sulphate ions in natural and industrial environments

List some of the common sources of sulphate ions in natural and industrial environments. For a given sulfate concentration, explain which of the following solutions would be the most deleterious and which would be the least deleterious to a permea..

  Calculate air flow required in cfm to transfer in hvac duct

Calculate the Air flow required in CFM to transfer 5,004 BTU/Hour in an HVAC duct given that the temperature difference (Delta-T) between the room and the supply air is 23 DegF.

  Explain indicated concentrations of total volatile solids

Influent sample collected from a wastewater treatment plant was analyzed for various solids concentrations. Results indicated concentrations of Total Volatile Solids (TVS)

  Smallest standard commercial pipe

For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of water gage. Determine the smallest standard commercial pipe that will give the required performance.

  How to label turing points numerically starting with tp1

A differential leveling loop started and closed on BM Juno, elevation 5194.02 ft. The BS and FS distancces were kept approximately equal. Readings (in ft) listed in the order takken are 9.65, 2.11, 2.51, 8.35, 2.06, 9.25, 7.93, 2.83, 5.05, and 4.6..

  What are the additional treatment processes required and why

Discuss the role of each physical, chemical and biological unit operations and processes employed in the wastewater treatment facility. If this treatment facility is required to supply class A recycle water to those industries for non-potable use

  What is the average waiting time of vehicles in the queue

A freeway has a capacity of 4500 veh/hr. A traffic accident occurs at 9AM and the freeway is closed. At 9:15 AM, the freeway is partially opened with capacity of 1500 veh/hr. Freeway is restored to full capacity 4500 veh/hr at 9:30 am.

  Develop a spreadsheet application that will display in table

develop a spreadsheet application that will display in a table the values of modulus of elasticity Ec for concrete having unit weight ranging from 95 pcf to 155 pcf (in steps of 5 pcf) and compressive strength ranging from 3500 to 7000 psi

  Deflection of a simple uniformly loaded beam

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  What is value of p that make work of the two processes

If this two-step process is replaced by a single isothermal expansion of the air from 800 K and 4 bar to some final pressure P, what is the value of P that make the work of the two processes the same

  What is the maximum distance between the two particles

Before the second particle catches the first particle, what is the maximum distance between the two particles.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd