Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. An aluminum plate 4 mm thick is mounted in a horizontal position, and its bottom surface is well insu- lated. A special, thin coating is applied to the top surface such that it absorbs 80% of any incident solar radiation, while having an emissivity of 0.25. The density p and specific heat c of aluminum are known to be 2700 kg/m3 and 900 J/kg · K, respectively.
(a) Consider conditions for which the plate is at a temperature of 25°C and its top surface is suddenly exposed to ambient air at T00 = 20°C and to solar radiation that provides an incident flux of 900 W/m2. The convection heat transfer coefficient between the surface and the air is h = 20 W/m2 · K. What is the initial rate of change of the plate temperature?
(b) What will be the equilibrium temperature of the plate when steady-state conditions are reached?
(c) The surface radiative properties depend on the spe- cific nature of the applied coating. Compute and plot the steady-state temperature as a function of the emissivity for 0.05 s 1, with all other conditions remaining as prescribed. Repeat your calculations for values of aS = 0.5 and 1.0, and plot the results with those obtained for aS = 0.8. If the intent is to maxi- mize the plate temperature, what is the most desirable combination of the plate emissivity and its absorptivity to solar radiation?
steam enters an adiabatic turbine at 5 mpa and 500degc with a mass flow rate of 5 kgs and leaves at 100 kpa. the
Compute the coordinates of the midpoint of the couple DE. Use Maple to plot the coupler curve for this point as a function of the input angle θ and calculate the mobility of the linkage
what is the moment as the bottom of a telegraph pole that is 50m high adn 25cm in diameter in a 34ms wind? the
but they vary in number of outputs, interfacing, cascadability, current limiting, and drive capability. As always, examine the data sheets carefully before substituting these parts! What is a Capacitor?
natural gas is a mixture of methane ethane propane and butane...as well as other components. consider natural gas
a loudspeaker is modeled with the following three equations.mx bx blittecoil blxldidt ri va - blxfind a transfer
determine diameter of a circular rod of ductile material with a fatigue strength ,e=280 Mpa. Add a tensile yield strength of 350 Mpa. The member is subjected to a varying axial load from 700 kN to -300kN. Assume Kt=1.8 and factor of safety=2.
an automotive repair shop stock many sizes of tires. one particular size and model is purchased for 15 and sold for 30.
A turbine uses steam at 25MPa and 650°C at the turbine inlet to generate 17.5MW of power. The steam enters the turbine at a rate of 90000kg/h. A portion of the steam passing through the turbine is removed for the purposes of feedwater heating (Figure..
A gentry structure, similar to a tire swing, is used to test the response of an airplane is hoisted back until the 20m swing cable is at theta=60. Determine the speed of the plane just before crashing into the ground at theta=15, when released from r..
starting from the general form of the heat equation in cylindrical coordinates for a system write an equation for the
A closed rigid, well-insulated tank contains 2 kg of saturated mixture of water at 159kPa. Initially, three-quarters of the mass in the tank is saturated liquid. An electric resistance heater placed in the tank is connected to a 11-V source and curre..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd