Coefficient of friction at the tool and chip interface

Assignment Help Mechanical Engineering
Reference no: EM13707038

A cutting tool (0.250in wide, rake angle 5 degrees) is used to machine in orthogonal mode. the depth of cut is 0.010in and the chip thickness is 0.027in. Calculate the shear angle and coefficient of friction at the tool and chip interface?

Reference no: EM13707038

Questions Cloud

What is the initial velocity of the ball in the y direction : A baseball is hit at ground level. The ball is observed to reach its maximum height above ground level 2.5 seconds after being hit. What is the initial velocity of the ball in the y direction
Calculate the specific heat at constant pressure : Calculate the specific heat at constant pressure (cp) and the specific heat and constant volume (cv) for air (jama = 1.4 ). The gas constant is given as R= 8.31446 J/molK.
How far apart are they after 1.8 h : Two airplanes leave an airport at the same time. The velocity of the first airplane is 720 m/h at a heading of 12.6 degrees. How far apart are they after 1.8 h
Obtain the equivalent spring constant of the rubber bands : A slingshot consists of a light leather cup attached between two rubber bands. It takes a force of 28 N to stretch the bands 1.3 cm. What is the equivalent spring constant of the rubber bands
Coefficient of friction at the tool and chip interface : A cutting tool (0.250in wide, rake angle 5 degrees) is used to machine in orthogonal mode. the depth of cut is 0.010in and the chip thickness is 0.027in. Calculate the shear angle and coefficient of friction at the tool and chip interface?
What speed must the player give the ball : A 78 g basketball is launched at an angle of 57.6? and a distance of 19.2 m from the basketball goal. What speed must the player give the ball
Maximum shear stress in the shaft and the angle of twist : A solid circular shaft made of 304 stainless steel uniformly tapers from a diameter of 1.5 inches to a diameter of 1.0 inches over a length of 3 feet. Objective: If the shaft transmits 100 hp at 2000 RPM, determine the maximum shear stress in the sha..
Find the magnitude of electric field produced by the disk : A disk of radius 2.3 cm has a surface charge density of 7.6 µC/m2 on its upper face. What is the magnitude of the electric field produced by the disk
High-performance automotive driveshaft : A high-performance automotive driveshaft is to be made of a 4-inch outer diameter 6061-T6 Aluminium tube. The shaft is to transmit 500 hp at 3000 rpm and requires a minimum factor of Safety against a shear yield failure of 3.0. Objective:

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Compare the relative properties and cost of three ceramic

some of our modern kitcgen cookware is made of ceramic materials. a compare the relative properties and cost of three

  What is the first order angular separations

The hydrogen spectrum has a red line at 656 nm and a blue line at 434 nm. What is the first order angular separations between these two spectral lines obtained with a diffraction grating that has 4500 lines per centimeter?

  A disk has a radius of 2 cm and weighs 12 kg what is the

a a disk has a radius of 2 cm and weighs 12 kg. what is the required constant moment to rotate the disk from rest to a

  Air at 15 degc and atmospheric pressure is forced over the

water at the rate of 0.8 kgs at 93 degc is forced through a 5 cm id copper tube at a suitable velocity. the wall

  If the plane becomes airborne at a speed of 270 kmhr

an airplane has a mass of 30mg and its engines develop a total thrust of 50kn during take-off. if the drag d exerted

  A steel plate which is 15 m by 15 m and 30 mm thick is

a steel plate which is 1.5 m by 1.5 m and 30 mm thick is lifted by four cables attached to its corners that meet at a

  A 100ft cable is made using a 12-gauge 01055in steel wire

a 100ft cable is made using a 12-gauge 0.1055in steel wire and three strands of 10gauge .1019in copper wire. find the

  What vertical distance do the two stones miss

Two girls standing 20 m apart are both throwing balls towards a tree to knock down a shoe hanging 7 m up in a tree that is directly between them. Girl A is 7 m from the tree while Girl B is 13 m from the tree.

  A force of 100 n is applied at the mid-point of cd angle of

the dimensions of a four bar link mechanism ab 400 mm bc 600 mm cd 500 mm ad 900 mm . a force of 100 n is applied

  At what rate must the chiller dump energy to the

a chiller is providing 5 tons of cooling to an air handler by cooling water transfer between the two devices. the

  The specific heats above and below the freezing point are

a mass of 1200kg of fish at 20 celsius is to be frozen solid at -20 celsius. the freezing point of the fish is -2.2

  At the end of the compression stroke the air is at 800 k

at the beginning of the compression stroke the volume of a certain diesel engine cylinder is 1 liter and it is filled

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd