Choose the technique that is best suited for the problem

Assignment Help Civil Engineering
Reference no: EM13304871

given f(x) = -2x^6 - 1.5x^4 + 10x +2. use a root location technique to determine the maximum of this function. perform iterations until the approximate relative error falls below 5%. if you use a braketing method use initial guesses of xl= 0 and xu= 1. if you use the newton raphson or the modified secant method, use an initial guess of xi= 1.if you use the secant method, use initial guesses of xi-1=0 and xi=1.assuming that the convergence is not an issue, choose the technique that is best suited for this problem. justify your choice.

Reference no: EM13304871

Questions Cloud

Report on the mini literature review : The report on the mini literature review (3 journal articles) will be assessed on how well the journal articles are integrated, analysed, discussed and leading to the research questions_that you will use in the interview. A literature review is n..
What was dollar amount of retained earnings after transfer : If retained earnings was $280 million prior to the transaction, what was the dollar amount of retained earnings after the transfer?
What is the density of the life jacket : An 81 kg person puts on a life jacket, jumps into the water, and floats. The jacket has a volume of 3.1 x 10-2 m3, What is the density of the life jacket
Explain and identify and explore contemporary challenges : Identify and explore contemporary challenges and opportunities in information systems and to formulate an opinion or judgement and offer possible solutions.
Choose the technique that is best suited for the problem : given f(x) = -2x^6 - 1.5x^4 + 10x +2. use a root location technique to determine the maximum of this function. perform iterations until the approximate relative error falls below 5%.
What is the force that the towrope applies to the skier : A skier of mass 64 kg is being towed up a slope ( µ = 15 ±) by a towrope at a constant speed of 3 m/s, what is the force (in N) that the towrope applies to the skier
How much will you have to invest year between now and then : It appears the annual payment required to reach your target is more than you can afford. If the most you can afford to invest each year is $1,200 what average annual rate of return must you earn in order to reach your target?
Determine the major and minor principal stresses at failure : Determine the major and minor principal stresses at failure and the effective stress friction angle (assume c' = 0). Plot the Mohr diagram.
Determine the net present value of the laser : Determine the Net present Value of a machine that takes little plastic boxes to hold a variety of playing cards. The machine requires an initial investment of $750,000 and will return $200,000 in cash flow per year for exactly five years. The rele..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine diameter of solid shaft if it is to transmit 50hp

If the allowable shear stress is 15ksi, determine the diameter of a solid shaft if it is to transmit 50hp at a frequency of (a) 900rpm, (b) 1800rpm

  Calculate the ph of the solution

A 1.50 L buffer solution is 0.250 M in HF and 0.250 M in NaF. Calculate the pH of the solution after the addition of 0.0500 moles of solid NaOH. Assume no volume change upon the addition of base. The Ka for HF is 3.5 x 10-4.

  Find allowable load p that can be supported by connection

A steel bar is attached to a wood support beam with four 20 mm diameter lag screws. The steel bar is 75-mm-wide by 6-mm-thick. For the steel bar, the yield strength is 260 MPa and the ultimate bearing strength is 350 MPa.

  How to plot the shear and moment across the beam

Write the equations required to express the shear and moment along the entire length of beam. Use an origin at point A, and then repeat computations using an origin at point D. Plot the shear and moment across the beam.

  Determine maximum allowable compressive force can be applied

The force is applied at the two pins. The pins allow rotation around the z-axis and do not allow rotation around the y-axis. The length of the beam between the pins is 8m. Determine the maximum allowable compressive force that can be applied.

  Determine the velocity and acceleration of point c of belt

determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off. (b) 9 s later.

  Determine what is flexural rigidity ei of the diving board

Consider a diver weighing 200 lb at the end of a diving board that cantilevers out over 3 ft. The diver oscillates at a frequency of 2 Hz. What is the flexural rigidity EI of the diving board

  Determine what is the thermal stress generated in the rod

The ¼" thick 6061?T6 aluminum bar is subjected to a tensile force of P = 5 kips. b = 4"; c = 1.5"; d = 2.5"; and the fillet radii are 1". a) Determine the maximum stress in the bar. b) What is the lateral strain in the 1.5" wide section

  Determine the maximum altitude reached by the rocket

A powered model rocket is launched in the vertical direction. The altitude of the rocket is 100FT (above ground level) at the end of the powered portion of the flight. The rocket lands 19.676 seconds from the powered portion of the flight.

  Problem related to skaters with masses

Physics two skaters with masses of 65 kg and 45 kg, respectively stand 8.0 m apart each holding one end of a rope.

  Determine the pressure difference between a and b

Fluids A and B ave specific gravities .75 and 1.00 respectively. If the mercury is used as manometer liquid determine the pressure difference between A and B

  Determine what is the static height reading of manometer

A manometer of water reads a height of 20cm at a temperature of 15 degrees C. If the diameter of the manometer tube is 1mm, what is the static height reading

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd