Cauldron of boiling liquid with a pulley system

Assignment Help Mechanical Engineering
Reference no: EM13718982

A witch lifts her cauldron of boiling liquid with a pulley system. Once the cauldron is lifted, liquid issues from two identical holes of cross-sectional area 2,000 mm2 (each) with a velocity of 30 m/s. The liquid sprays 30o below the horizontal. Calculate the force P required to give the cauldron an upward acceleration of 0.5 m/s2 from rest if it contains 40 kg of liquid at the time. The mass of the cauldron itself (when empty) is 20 kg. Assume the density of liquid to be that of water.

Reference no: EM13718982

Questions Cloud

Domestic how water supply : Steam at 500KPa 300 C is used to heat cold water at 15 C to 75 C for domestic how water supply. How much steam per kg liquid water is needed i the steam should not condense?
Saturated liquid entering and saturated vapor exiting : A Carnot power cycle operates at steady state with water as the working fluid. The boiler pressure is 200lbf/in^2, with saturated liquid entering and saturated vapor exiting. The condenser pressure is 20lbf/in^2.
Air flows with heat exchanger : Air at 600k flows with 3 kg/s into a heat exchanger and out at 100 C. How much (kg/s) water coming in at 100 KPA, 20 C can the air heat to the boiling point?
Clockwise without slipping on the fixed horizontal surface : At the instant shown, the rigid body OA rolls counter clockwise without slipping on the fixed horizontal surface, and point O has a velocity 2 m/s to the left and an acceleration of 1 m/s2 to the right. Point O is at the center of the semi-circle reg..
Cauldron of boiling liquid with a pulley system : A witch lifts her cauldron of boiling liquid with a pulley system. Once the cauldron is lifted, liquid issues from two identical holes of cross-sectional area 2,000 mm2 (each) with a velocity of 30 m/s. The liquid sprays 30o below the horizontal.
Energy when completely combusted in air : As a 75 slug car travels along a horizontal, 3200 ft section of road, it changes speed from 5 mph to 60 mph. During this acceleration, the car gets an average MPG of 15 MPG. How efficient is the car’s engine during the acceleration assuming 1 gallon ..
Calculate starin in axial and transverse direction : A 10-ft long rectangular ASTM Grade 50 steel plate 1-in by 12-in cross section is used as a hanger and is subjected to a tensile load of 240,000 lb . the modulus of elasticity for steel is 30,000,000 psi and the poison ratio is 0.25
Compute the stress-strain and total elongation : A 24 in long bar with a cross sectional area of 1.0 in^2 is subjected to an axial tensile load of 10,000 lb. compute the stress, strain and the total elongation if the bar material is :
Determine the air velocity at the exit when inlet velocity : The exhaust nozzle of a jet engine expands air at 388 kPa and 174 C adiabatically to 95 kPa. Determine the air velocity at the exit when the inlet velocity is low and the nozzle isentropic efficiency is 96 percent.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Compute the fugacity’s of ethane and n-butane

Compute the fugacity’s of ethane and n-butane in an equimolar mixture at 373.15K at 1, 10, and 15 bar total pressure assuming that the Lewis-Randall rule is correct.

  Find the critical speed when the trailer is traveling over

the springs of an automobile trailer are compressed 10.6 cm under its weight. find the critical speed when the trailer

  What is the temperature and state of the steam in the pipe

a) What is the temperature and state of the steam in the pipe? b) What is the quality of the steam in the pipe?

  Determine the coefficient of static friction between each

the 5-kg rm kg cylinder is suspended from two equal-length cords. the end of each cord is attached to a ring of

  How long should the roughing section be what pull must the

a roughing section of a broach is to remove stock 3.2 mm deep from a steel surface205 mm long x 50 mm wide each tooth

  Determine the specific entropy of the steam at the turbine

steam enters an adiabatic turbine at 8 mpa and 520 degc with a volumetric flow rate of 0.8 m3s and exits at 30 kpa. the

  Velocity at the moment is v518 ms density p613 kgm3 assume

a spherical container with volume 0.05m3 is pressurized up to 800kpa absolute pressure. air is released suddenly

  Specimen of aluminium having a rectangular cross section

A specimen of aluminium having a rectangular cross section 9.9 mm × 13.0 mm (0.3898 in. × 0.5118 in.) is pulled in tension with 35300 N (7936 lbf) force, producing only elastic deformation. The elastic modulus for aluminium is 69 GPa (or 10 × 10    6..

  Consider the 2d inviscid flow over a body of some known

consider the 2d inviscid flow over a body of some known shape. write down general expressions for the total aerodynamic

  Derive an expression for the compressibility of air

derive an expression for the compressibility of air represented by tau for 1 and isothermal process and 2 for an

  The pressure and temperature at the end of compression

an engine operates on an air standard otto cycle with the compression ratio of 91. the pressure and temperature at the

  An ammonia absorption refrigeration cycle requires 2500

an ammonia absorption refrigeration cycle requires 2500 btulbm heat transfer in the generator.saturated vapor leaves

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd