Can one collector be temporarily taken out of service by

Assignment Help Civil Engineering
Reference no: EM13563765

Dust is removed from the airstream of a municipal incinerator by four dust collectors operating in parallel, each handling 1/4 of the total airflow of 200 m3/min. The airstream contains 10 g/m3 of suspended solids. The collector efficiency is 98%, decreasing linearly to 74% as air flow is doubled. If the maximum permissible solids concentration from the combined stack discharge [all 200 m3/min] is 1.0 g/m3, can one collector be temporarily taken out of service by: (a) overloading the other 3 units [i.e., each of the three handling 1/3 of the total flow], or (b) by not treating 1/4 of the airflow [i.e., mixing 150 m3/min of treated air with 50 m3/min of untreated air]?

Reference no: EM13563765

Questions Cloud

Estimate a value of msw generation in the year 2025 : The United States Environmental Protection Agency (EPA) has published the following data for municipal solid waste generation (in millions of tons).
What percent removal efficiency may be expected under : A cyclone separator is being used to remove particulates from a gas stream. The current removal efficiency is 96% for an air flow rate through the separator equal to 18 m3/s. Due to a process change, the air flow rate is expected to increase to 22 m3..
Calculate a value of temperature that could be used : A correlation for particulate removal efficiency in an electrostatic precipitator (n) as a function of gas velocity (u) may be written in the form: n = 1 - e^-k / u.
Determine the proportional limit stress the modulus : At the proportional limit, a 32-mm-thick by 87-mm-wide bar elongates 10.2 mm under an axial load of 532 kN. The bar is 2.4 m long. Poisson%u2019s ratio, , for the material is 0.27.
Can one collector be temporarily taken out of service by : Dust is removed from the airstream of a municipal incinerator by four dust collectors operating in parallel, each handling 1/4 of the total airflow of 200 m3/min. The airstream contains 10 g/m3
Design the flexural reinforcement for this member : A rectangular concrete beam of width b = 24 inches is limited by architectual considerations to a maximum total depth of h = 16 inches. it must carry a total factored load moment of Mu = 400 ft-kips. Design the flexural reinforcement for this member,..
Calculate the emissions of sulfur dioxide : Calculate the emissions of sulfur dioxide, particulates (fly ash), and carbon dioxide per kilowatt-hour of electrical energy produced. Assume that all of the carbon in the coal is released to the atmosphere.
What is the second year book value for equipment with : What is the second year book value for equipment with an initial cost of $11,000, a salvage value of 1,000 and a recovery period of 5 yrs for A. straight line depreciation. B. Double declining balance. C. MACRS?
What are the adjusted elevations for benchmarks b c and d : Differential leveling between benchmarks A,B,C,D, and A gives elevation differences(m) of -15.632, 32.458, 38.214, and -55.025, and distances(km) of 4,6,5, and 3 respectively.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What will the volume of the sample be for the water content

a saturated 100 cm^3 clay sample has a natural water content of 30 percent. it is found that the shrinkage limit occurs when the water content is 19 percent. if the specific gravity of soil solids is 2.70

  Determine the restraining force by a concentric reducer

The pipe is connected to a 400mm diameter pipe by a concentric reducer, the gauge pressure at the entrance of the reducer is 3.00 bar and the the energy losses are neglected . Determine the restraining force.

  What is the angular rotation rate after front wheel contacts

A car is traveling toward a 20 degree slope at 60 mph. The wheels have a radius of 12 in, and the car's wheelbase is 100 in. What is the angular rotation rate of the car immediately after the front wheel contacts the slope

  Determine consequent compressive stress in the curtain wall

Because of the insulation between them, the sun heats up the wall panel 120 degrees F but the column to 80 degrees F. Determine the consequent compressive stress in the curtain wall.

  What is the resultant force on one side of a 25cm diameter

What is the resultant force on one side of a 25cm diameter circular plate standing at the bottom of 3m of pool water

  Determine what type of surface would wheeler tractor be

A wheeled tractor with high-pressure tires and weighing 74,946 lb is pulled up a 5% slope at uniform speed. If the tension in the tow cable is 13,000 lb, what is the rolling resistance of the road

  What is coefficient of static friction on verge of sliding

A chair weighing 150 rests on a level floor that is not frictionless. A man pushes on the chair with a force = 43.0 that is directed at an angle of 34.0 with the horizontal. Assume that the chair is stationary but is on the verge of sliding.

  Determine the critical crack length to assure the plate will

Consider the same plate under the action of cyclic tensile/compressive stresses of 120MPa and -30 MPa, respectively. If the component is to remain safe for 10 million cycles, what is the largest allowable crack length?

  Why would it be incorrect to use the velocity in the larger

An engineer would like to make a physical model of the molasses flow but use water instead of molasses. How much would the velocity and the radius  of the pipe have to change to keep the flow dynamically similar

  What input of power rating is required for the pump

A water storage tank located on a larege dairy farm has a storage capacity of 0.1 ML. The average rate of water consumption from this tank is 6.25 kL per day, every day.

  Determine the normal depth using a converging iteration

A 5-m wide rectangular channel is carrying a flow of 5 cubic meter per second. If the Manning n=0.013 and the bottom slope, So=0.0001, determine the normal depth using a converging iteration.

  At what minimum slope can it be laid such that the velocity

A circular PVC plastic (smooth) storm sewer has a diameter of 18 in. At the design flow, it is intended to have a relative depth of 0.8. At what minimum slope can it be laid such that the velocity is at least 2 ft/s at design flow and depositied soli..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd