Calculate the wind force on the turbine for a 5 mph wind

Assignment Help Electrical Engineering
Reference no: EM13269656

A horizontal axis wind turbine has a blade span of 2 meters in diameter and is mounted on a 3-meter-tall tower. a) Calculate the wind force on the turbine for a 5 mph wind. b) What is the force if the wind speed is tripled? c) Calculate the torque on the tower for the cases of the 5 and 15 mph wind velocities

Reference no: EM13269656

Questions Cloud

What was your total real rate of return on this investment : If the inflation rate last year was 4 percent, what was your total real rate of return on this investment?
Find the coil resistance of the motor : A vacuum cleaner is plugged into a 120.0-V socket and uses 2.4 A of current in normal operation, Find the coil resistance of the motor
What is the air conditioner''s coefficient of performance : An air conditioner removes 5.0 * 105 J/min of heat from a house, What is the air conditioner's coefficient of performance
Globalization and offshoring : Why, how, and whether the issue has become a social issue rather than simply remain a private issue? What do you see as the responsibilities of the affected individuals?
Calculate the wind force on the turbine for a 5 mph wind : a) Calculate the wind force on the turbine for a 5 mph wind. b) What is the force if the wind speed is tripled? c) Calculate the torque on the tower for the cases of the 5 and 15 mph wind velocities
Find the after-tax rates of return on all three securities : Shrieves's corporate tax rate is 40%, and 70% of the dividends received are tax exempt. Find the after-tax rates of return on all three securities. Round your answers to two decimal places.
Find what is the energy per bit for the bpsk pulse : Consider a BPSK signal where each bit is represented by a triangular pulse with width T and height A. What is the "energy per bit" for this BPSK pulse with A=7V and T=0.008s
What is the amount of the endowment required : What is the amount of the endowment required to establish the center and supply the funds to maintain this center forever?
What is the change in the wires resistance : A copper wire has a 25-m ohm resistance at 20 degrees C. When the wire is carrying a current, What is the change in the wire's resistance

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the initial charge on the capacitor

If a 2 microfarad capacitor is charged to 12 volts and then connected across a resistor of 100 ohms: Determine the initial charge on the capacitor, initial current through the 100 ohm resistor and the time constant.

  Determine what is the relative dielectric constant

A uniform plane wave propogates in the positive z direction with a frequency of 20 MHz. A probe is at z=0 m measuring the phase to 98 degrees and another probe at z= 2 m measures the phase to be -15 degrees what is the relative dielectric constant..

  What is the output voltage of differentila amplifier

In the differential amplifier shown in the schematic, R1 = R2 = 10 k ohm; R3 = R4 = 100 k ohm. Assume the ECG voltage at V1 = 100 mV, and the ECG voltage at V2 = - 100 mV. There is a power line interference of 200 mV at both input sites.

  Design the logic for address decoder-glue logic and dtack

A Motorola 68000 microprocessor-based data acquisition system incorporates memory ( EPROMS and SRAMS), an Analog-to-Digital Converter (A/D), a Centronics Parallel Printer, and a very simple I/I Device made up of a single push-button switch.

  How to draw schematic of circuit that implements logics

How do you draw a schematic of a circuir that implements any of the following: a circular left or a right shift of 0-3, or a logical left or right shift of 0-3

  Determine the rate of return for the project

A new project has the following predicted profits. The initial investment is $3,000,000. Yr Revenue 1 $200,000 2 $400,000 3 $600,000 4 $800,000 5 $1,200,000 6 $1,200,000 7 $1,400,000 8 $1,600,000

  Determine min step size e necessary to avoid slope overload

consider a message signal m(t)= e^(-2t) cos(2000*pi*t) u(t) a) determine the minimum step size E necessary to avoid slope overload b) calculate the minimum avaerage quantazation noise power based on part a

  Design the electrical system for a shopping center

Design the electrical system for a shopping center with 500,000 square feet at least 30 spaces of three different sizes (5,000, 10,000 and 25,000 sf). They may be offices, banks, restaurants and shops.

  Find the terminal voltage of the motor and power factor

A three phase synchronous motor has the synchronous reactance of 2.1 Ohm and draws 250 A with a lagging power factor for an excitation voltage of 1327 -15 degree per phase. Find the terminal voltage of the motor and power factor of the motor.

  Calculate amount of work done if all losses are neglected

A container with a plunger compresses one pound mole of an ideal gas from 1 atmospheres pressure to 10 atmospheres. Calculate the amount of work done if the process is considered to be polytropic.

  Calculate the infinite slopes when they are operating

What happens when you have a non-zener and zener diode in series opposing each other eg non-zener is forward bias and the zener is reverse bias assuming both are ideal (infinite slopes when they are operating).

  Find what is the approximate center frequency of the filter

An SSB generator has a 9 MHz carrier and is used to pass voice frequencies in the 300- to 3300-Hz range. The lower sideband is selected. What is the approximate center frequency of the filter needed to pass the lower sideband

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd