Calculate the pressure

Assignment Help Mechanical Engineering
Reference no: EM131324124

Problem -

a. Consider a one-component system consisting of spherical bubbles of vapor inside a liquid, which is commonly observed as a liquid begins to boil. This is similar to the case considered in class in which liquid droplets were suspended in a vapor, but the identity of the phases is reversed (here α = liquid, β = vapor). If the liquid is in equilibrium with the vapor in the bubbles, it can be shown that:

VβdPβ = ΔHv(dT/T)

where T is the boiling temperature. Beginning with this equation, derive the following equation showing the variation of boiling temperature with bubble size:

(1/To) - (1/Tr) = (R/ΔHv)ln(1 + (2γ/rPα))

Briefly explain any non-mathematical steps. Assume that the vapor can be treated as an ideal gas and state any other assumptions you make.

In this equation:

To = boiling temperature for a flat interface, K

Tr = boiling temperature for the liquid layer surrounding a bubble of radius r, K

ΔHv = enthalpy of vaporization, J/mole

γ = surface energy of the liquid/bubble interface, J/m2

b. For liquid Na, the 1 atm boiling temperature is 1150 K for a flat liquid-vapor interface, ΔHv = 101.3 kJ/mole and γ = 0.19 1/m2. If the liquid pressure is 1 atm, calculate (i) the pressure (in atm) inside a Na bubble with a radius of 1 μm and (ii) the boiling temperature for the liquid layer surrounding a Na bubble with a radius of 1 μm.

Reference no: EM131324124

Questions Cloud

What you accomplished with your configuration : What you accomplished with your configuration? What operating systems does it run on (usually either Linux and/or Windows)? What dependencies does it have (meaning, what is required for it to run)?
Sales increase firm net operating income : How much will a 10% increase in sales increase a firm's net operating income (NOI) and increase its net income (NI), if: its degree of operating leverage (DOL) = 2.0, and its degree of financial leverage (DFL) = 3.0? (b) its DOL = 2.5 and DFL = 4.0?
Is the futures overpriced or underpriced : Assuming continuous compounding, suppose the risk-free rate is 5.96 percent, and the dividend yield on the index is 2.75 percent. Is the futures overpriced or underpriced?
Market because of severe adverse effects and several deaths : You read in the newspaper about a recently approved prescription drug that has suddenly been withdrawn from the market because of severe adverse effects and several deaths.
Calculate the pressure : For liquid Na, the 1 atm boiling temperature is 1150 K for a flat liquid-vapor interface, ΔHv = 101.3 kJ/mole and γ = 0.19 1/m2. If the liquid pressure is 1 atm, calculate (i) the pressure (in atm) inside a Na bubble with a radius of 1 μm and (ii) ..
Current accelerated rate of approval of a new drug : Give a drug example to support your position. Then, take a different position and support the current accelerated rate of approval of a new drug in the United States.
Find the futures price : To induce investors to buy futures contracts, a risk premium of $4 is required. To store the commodity for the life of the futures contract would cost $5.50. Find the futures price.
Income capitalization converts income to value equivalent : Small income properties are bought and sold only for their tangible amenities. Gross income multipliers normally increase with a decrease in the operating expense ratio. Rent for the manager's unit should be included in the rent forecast. Income capi..
What does it mean to say the files were randomly selected : What does it mean to say the files were randomly selected?How would the researcher randomly select files? In other words, what does the process look like?Would our probabilities and results be different if we used convenience sampling? Why or why not..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the maximum permissible value of the load q

Determine the maximum permissible value of the load q if the allowable bending stress in the shelf is σallow= 7.5 MPa and the position of the supports is adjusted for maximum load carrying capacity.

  Estimate the daily heat loss through the wall

Assuming quasi steady conditions for which changes in energy storage within the wall may be neglected, estimate the daily heat loss through the wall if its total surface area is 200 m2.

  Calculate the specific weight of toluene

Calculate the specific weight of toluene at a place where the acceleration of gravity is 32.2 ft/s^2or 9.81 m/s^2. Express your answer in both lbf/ft^3 and kg/m^3. Repeat this for Mars whre the acceleration due to gravity is 37.5% of that on Earth.

  Determine net work developed per cycle-thermal efficiency

1 kg of a gas in a piston-cylinder assembly undergoes a Carnot power cycle for which the isothermal expansion occurs at 800 K. The change in specific entropy of the gas during the isothermal compression, which occurs at 400 K is -25 kJ/kg. K. Determi..

  How much a and ß are in the eutectic microconstituent

Determine the composition of the alloy and whether it is hypoeutectic or hypereutectic.

  What is the overall effectiveness of each screen

Assuming the analyses are accurate, what do they show about the ratio by weight of each of the three fractions actually obtained? What is the overall effectiveness of each screen?

  Estimate the critical heat flux

The bottom of a copper pan, 0.3 m in diameter, is maintained at 118°C by an electric heater. Estimate the power required to boil water in this pan. What is the evaporation rate? Estimate the critical heat flux.

  Find the angular acceleration at the moment

the mean values of the angular velocity and angular acceleration averaged over the time interval between t = 0 and the complete stop

  Calculate its specific gravity at each temperature

A certain medium lubricating oil has a specific weight of 8.860 kN/m3 at 5°C and 8.483 kN/m3 at 50°C. Calculate its specific gravity at each temperature.

  What is the percent increase in the smaller section

What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)?

  Given n1000 lb e30x106 psi upsilon03 l4 ft gamma0283 lbin3

given n1000 lb e30x106 psi upsilon0.3 l4 ft gamma0.283 lbin3 and a 4x4 hollow square tube beam cross section with a

  The plant generates 20mw of electricity and uses coal with

a power plant has an overall efficiency of 30. the plant generates 20mw of electricity and uses coal with a heating

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd