Calculate the percentage power saving

Assignment Help Mechanical Engineering
Reference no: EM13867872

QUESTION 1

a) Calculate the percentage power saving when the carrier and one of the sidebands are suppressed in an AM wave modulated to a depth of 100 %.

b) The total power content of an AM signal is 1000 W. Determine the power being transmitted at the carrier frequency and at each of the sidebands when the percent modulation is 100%.

QUESTION 2

The FM wave voltage equation is represented as:

v = 12sin (6 * 108t + 5sin 1250t)

Find the:

i) carrier and modulating frequencies

ii) modulation index

iii) maximum deviation

iv) value of power this FM wave will dissipate in a 10W resistor

Reference no: EM13867872

Previous Q& A

  Why you think ethics matter in policy development

Explain why you think ethics matter in policy development. Identify the ethical considerations that must be taken into account when drafting or designing a policy

  Problem regarding the rankine cycle

1) An ideal Rankine cycle which uses water as the working fluid operates its condenser at 40oC and its boiler at 300oC. The mass flow rate of steam entering the turbine is 100 kg/s. Determine the following;

  Determine how you would intervene as a facilitator

Create a 5- to 6-page paper critiquing the group's functioning regarding its processes and dynamics by addressing the following: Determine how you would intervene as a facilitator

  Determine first and third quartiles for federal savings bank

Determine the first and third quartiles for Federal Savings Bank. Develop a box plot. Are there any outliers? Do the amounts follow a symmetric distribution or are they skewed? Justify your answer.

  Levered firm and an unlevered firm

levered firm and an unlevered firm

  Determine how you would intervene as a facilitator

Create a 5- to 6-page paper critiquing the group's functioning regarding its processes and dynamics by addressing the following: Determine how you would intervene as a facilitator

  Fourier transform-properties

Find and plot the frequency response of x(t)-Find and plot the frequency response of x(2t)

  Difference between a static budget and a flexible budget?

difference between a Static Budget and a Flexible Budget?

  Determine the first and third quartiles

Determine the first and third quartiles. Develop a box plot. Are there any outliers? Do the amounts follow a symmetric dis- tribution or are they skewed? Justify your answer.

  Why problem delineation and definition is so important

In a minimum of 300 words, post your responses to the following: Explain why problem delineation and definition is so important to the policy development process. Explain why it is necessary to outline the goals and objectives of a policy

Reviews

Write a Review

 

Similar Q& A

  Determine the efficiency of a single fin

A radiator wall measuring 2 m by 3 m (WxH) is held a temperature of 125 °C. Straight aluminum fins (k = 175 W/mK) are to be mounted on the wall. The fins are 5 cm in length and 0.8 mm thick. The system is allowed to convectively transfer heat to ambi..

  Individual gas and liquid mass transfer coefficients

A mass transfer tower operating at 1 atm and 300 K uses water, which enters free of ammonia at the top, to reduce the ammonia (NH3) concentration in air exhausted from a reactor. At one plane (W) in the tower, the concentrations of ammonia in the liq..

  Derive the dynamic equation for rp manipulation

Derive the dynamic equation for RP manipulation of example 6.5 (Introduction to robotics by Craig)by using newton-euler's dyanamics.

  Determine the magnitude of the average friction force

the 3.25-kg collar shown below is attached to a spring and released from rest at a. the collar then travels downward a

  Calculate the compressor outlet temperature

If the isentropic efficiency of the compressor is 72% and the pressure ratio is 2.2:1, for an inlet pressure and temperature of 1 bar and 25oC, calculate the compressor outlet temperature, the compressor outlet density and the power required to drive..

  How penalty method is applied on a one dimensional

how penalty method is applied on a one dimensional heat equation in Meshless method.

  Determine the minimum pipe diameters required to restrict

consider a steam turbine in which steam enters at 10.45 mpa and 780k with a flow rate of 38.739 kgs. a portion of the

  If this bullet was fired into 1 lbm of water at room

a 9 mm bullet with mass 0.28 oz 0.0175 lbm exits a pistol at 1250 fts find the kinetic energy in btu. if this bullet

  Sketch the process on a p-v diagram indicating the relative

a piston-cylinder arrangement initially contains water at p 300 psia and t 500of. the piston is moved to a final

  Torsion spring to inverted pendulum

If you attach torsion spring to inverted pendulum, is this the equation of motion? The spring is attached on one end to a pivot point and also at the pivot point the spring is attached. I used L/2 for the location of the center of mass.

  A 456-kg girl is standing on a 141-kg plank both originally

a 45.6-kg girl is standing on a 141-kg plank. both originally at rest on a frozen lake that constitutes a frictionless

  A golfer hits a golf ball from point a with an initial

a golfer hits a golf ball from point a with an initial velocity of 50ms at an angle of 25 degrees with the horizontal.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd