Calculate the overall heat-transfer coefficient

Assignment Help Mechanical Engineering
Reference no: EM13705931

The outside wall of a refrigerated storage room is 10m long and 3m high and is constructed with 100-mm concrete blocks ( k=0.935W/m C) and 10 cm of fiber insulation board (k=0.048W/m C). The inside temp of the room is - 10 C and the convective heat transfer coefficient is 40 W/m2 K; the outside temp is 30 C with a convective heat transfer coefficient of 10 W/m2K on the outside wall surface. Calculate the overall heat-transfer coefficient. Please show work.

Reference no: EM13705931

Questions Cloud

Center of masses of the upper arm and the forearm acts : Assume that the center of masses of the upper arm and the forearm acts in the geometric center of the respective body segment, and the center of mass of the hand acts at the same location that the cable is in the hand (given below). If the person is ..
Circle item which is intensive properties : Please circle item(s) which is (are) intensive properties: Please circle the item(s) which can be considered as pure substance in Thermodynamics: Please circle the valid statement(s) about superheated vapor with temperature T and pressure P:
Piston-cylinder assembly undergoes a thermodynamic cycle : A gas within a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processes: There are no significant changes in kinetic or potential energy.
Etermine the force applied by the ram : A cube of 2" dimensions is placed in a square hole (also of 2" dimensions) that is 1.998" deep. The hole was cut out of a rigid material. (The top of the cube protrudes .002" above the surface). If a flat rigid plate is placed on top of the cube and ..
Calculate the overall heat-transfer coefficient : The outside wall of a refrigerated storage room is 10m long and 3m high and is constructed with 100-mm concrete blocks ( k=0.935W/m C) and 10 cm of fiber insulation board (k=0.048W/m
Metal cannot experience any plastic deformation : A metal cylinder metal cylinder 120.0mm long and 15 mm in diameter is to have a tensile force of 15000N applied. Which of alluvium, copper, brass, nickel steel and titanium are good options if the metal cannot experience any plastic deformation?
Determine the final volume and pressure : Air is expanded in a poly tropic process from a pressure and volume of 350 kPa and 0.03 m3 until its volume is increased by 6.667 times. The poly tropic process has an exponent n = 1.5
Estimate the amount of heat transferred by a single fin : The engine of my go-cart has circular fins, 3 mm thick that are machined into the aluminium of the cylinder (k=240 W/m*K) such that the outer diameter of the cylinder itself (not including the fins) is 10 cm and the fins stick out from the cylinder b..
Consider a slab of solid material of area : Consider a slab of solid material of area A between two large parallel plates a distance Y apart. Give the initial condition and the progression of events that proceeds with time as the lower plate is suddenly brought to a slightly higher temperature..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Motor is used to raise

A 100-watt motor (60% efficient) is used to raise a 100-kilogram load 5 meters into the air. How long, in units of seconds, will it take the motor to accomplish this task?

  Determine a the magnitude in km of the cars total

a car is driven east for a distance of 43 km then north for 23 km and then in a direction 29deg east of north for 27

  At the end of year 5 repair costs are 4000 and increase 500

a new product tracking machine costs 130000 and will have a 15000 salvage value at the end of 10 years. annual repair

  More energy is added with the paddle wheel until the

nitrogen r0.2968 kjkg-k cv 0.745 kjkg-k at 100 kpa is contained in an insulated piston cylinder device as shown in the

  Consider the piston area as 0012 m2 the piston mass as 6116

a 0.86 kg of saturated vapor steam contained within a piston-cylinder. initially the piston face is at x 0 and the

  What are some of the factors neglected in the theoretical

a why is it useful to plot the results on log-log graph paper rather than cartesian graph paperb what are some of the

  A piston-cylinder device initially contains 007m3 of

a piston-cylinder device initially contains 0.07m3 of nitrogen gas at 130kpa and 120 degrees celsius. the nitrogen is

  Determine the pressure p2 and p3 in pipes 2 and 3 under the

water flows through the horizontal y-fitting shown in figure p3.101. if the flowrate and pressure in pipe1 are q1 2.3

  An air-water vapor mixture at 01 mpa 30degc 80 rh has a

an air-water vapor mixture at 0.1 mpa 30degc 80 rh has a volume of 50 m3. calculate the specific humidity dew point wet

  For the 1st process deltae 20 kj and for the 3rd process

a thermodynamic system undergoes a cycle composed of a series of three processes for q1 10 kj q2 30 kj q3 -5 kj. for

  The following wind conditions are expected v 10 i - 5 j

from time t0 to t5 hr radioactive steam is released from a nuclear power plant located at x -1 mile and y 3 miles.

  If the air temperature is 60f at standard atmospheric

a pitot-static tube used to measure air velocity is connected to a differential pressure gage. if the air temperature

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd