Calculate the mass of steam condensed during this process

Assignment Help Civil Engineering
Reference no: EM13531130

A room is filled with saturated steam at 100 degrees C. Now a 5-kgbowling ball at 25 degrees C is brought to the room. Heat istransferred to the ball from the steam, and the temperature of the ball rises to 100 degrees C while some steam condenses on the ballas it loses heat (but it still remains 100 degrees c). The specificheat of the ball can be taken to be 1.8 KJ/kg*C. Calculate the mass of steam condensed during this process.

Reference no: EM13531130

Questions Cloud

Find the values of m and n : Use the ac test to determine if the following trinomial can be factored.  If it can be factored, find the values of m and n.
State which method should be applied as the first step : State which method should be applied as the first step for factoring the polynomial.
Rewrite the middle term as the sum of two terms and then : Rewrite the middle term as the sum of two terms and then factor completely.
How long does it take light traveling : The distance from a star to a planet is 3.1 * 1019 m.  How long does it take light, traveling at 1016 m/year, to travel from the star to the planet?
Calculate the mass of steam condensed during this process : A room is filled with saturated steam at 100 degrees C. Now a 5-kgbowling ball at 25 degrees C is brought to the room. Heat istransferred to the ball from the steam, and the temperature of the
With this method approximately 80liters of water are require : A meat packing plant manager is trying to decide between twodifferent methods for cooling cooked hams. the spray methodinvolves spraying water over the hams until the ham temperature isreduced to 30 degrees Celcius. With this method approximately 80l..
Estimate the tension in the rope if the wind : The intensity of Na light passing through a gold film wasmeasured to be about 15% of the incoming light. What is thethickness of the gold film? ( λ=589 nm; k=3.2).
What is the original unstretched length of the cable : A 57.0 kg skier is being pulled up a 13.0° slope by a steelcable. The cable has a cross-sectional area of 7.18 10-5 m2. The cable applies a force tothe skier
Determine the approximate drag coefficient for the parachute : A 5-m-diameter parachute of a new design is to be used to transporta load from flight altitude to the ground with an average verticalspeed of 3 m/s. The total weight of the load and theparachute is 200 N. Determine the approximate dragcoefficient for..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine rate of ammonia utilization nd biomass growth rate

Determine the rate of ammonia (NH4-N) utilization and the biomass growth rate for the following conditions: µm = 0.50 g VSS/g VSS-d Ks = 0.50 mg/L X = 10 mg/L S = 40 mg NH4-N/L

  Find the conjugate depths of the jump formed in a channel

The discharge through a 6.0 ft wide rectangular channel is 200.0 ft3/s. Find the conjugate depths of the jump formed in such a channel if 3.5 ft of energy head is lost through it.

  Select a hydraulic pump size and a hydraulic cylinder size

Hydraulic cylinders with a stroke of 72 inches are available with bore sizes from 2 o 8 inches. Hydraulic piston pumps with an operating pressure range from 200 to 3000 psig are available with pumping capacities of 5, 10, and 15 gallons per minute..

  Determine the cod

Determine the COD, carbonaceous BOD, and nitrogenous oxygen demand of a 100 mg/L solution of urea (N2H4CO)

  Compute the total energy per unit weight

A fluid flowing in a pipe 30cm in diameter has a uniform velocity of 4m/s. The pressure at the center of the pipe is 40KPa, and the elevation of the pipe's centerline above an assumed datum is 4.5m. Compute the total energy per unit weight of the ..

  Determine stress in member immediately after load is applied

You are analyzing a polymer uniaxial tension member used in a lightweight structure. The bottom of the tension member is fixed and the top has a tensile force F = 10,000 pounds on it.

  Calculate the detention time-hr in each clarifier

A waste water treatment plant previously used two circular clarifiers for primary settling, each 42 ft in diameter and 12 feet deep. Assume the incoming flow rate was 0.9 MGD. The maximum allowable clarifier loading rate is 600 gal/d/ft^2

  Compute the sample mean and medium sample

Suppose X is a continuous random variable with probability density function, f(x)=4x^3 for 0

  Determine the decay rate constant for the die-off of anthrax

The results of his experiment are tabulated below. Assuming the experiment was conducted in a completely-mixed batch reactor, determine the decay rate constant for the die-off of anthrax.

  Show by counter example that if f isnot onto then

Suppose that F1 ο G2 =F1ο G1 then F : S→ T, G1 : T → U, G2 :T →U,. Define a function F : R2 ? R2 by F(x, y) = (x +y, x - y). . Show that if F is onto, Suppose that G1ο F = G2 ο F.

  What force vector does the angled member apply

The linkage shown is made up of two 3-kg rectangular members (0.4 m by 0.1 m), and is flying through the air. At the instant shown, the vertical member has angular velocity 4 rad/s, and the angled member has angular velocity 1 rad/s.

  Determine the magnitudes of the components faa and fbb

Force F with magnitude indicated acts at point o. determine the magnitudes of the components Faa and Fbb along directions a-a and b-b so that F=Faa+Fbb

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd