Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.The velocity of propagation, c of surface waves is assumed to depend on the water depth, y, the water density, ?, and the acceleration due to gravity, g. Express these variables as a dimensionless group.
2.An ogee spillway of a gravity dam is to be modeled using water. The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet. Using a model scale of 1:10, calculate the height of the model.
3.Iron and vanadium both have the BCC crystal structure, and V forms a substitutional solid structure in Fe for concentrations up to approximately 20 wt% V at room temperature. Determine the concentration in weight percent of V that must be added to iron to yield a unit cell edge length of 0.289nm
For a 30ft simply supported beam, there is a uniform load of 1.5 k/ft. along the length and two point loads of 20 kips each spaced at (from x=0 to x=30ft left to right) x=10ft and x= 20 ft.
A hydroelectric facility operates with an elevation difference of 50.0 m with a flow rate of 500 m3/sec. If the rotational speed is 90 rpm, determine the most suitable type of turbine and estimate the power output of the arrangement.
A company has been discharging its waste into a holding pit for a long time. For the last several years, the pit has been full and overflowing into a local river. The waste concentration has been nearly constant at 10 mg/L of the pollutant of inte..
A simple four-leg intersection needs a 2-phase fixed-time signal. The critical flows in the N-S and E-w directions are 600 and 400 veh/hr, respectively, with a 0.95 peak-hour factor.
Assume you are observing traffic in a single lane of a highway at a specific location. you measure the average headway and average spacing of passing vehicles as 3 seconds and 150 ft, respectively. calculate the flow, average speed, and density of..
an observer has determined that the time headways between successive vechile on a section of the highway are exponentially distributed and that 65% of the headways btw vehicles are 9 seconds or greater.
(a) Determine the desired diameter of the disk. (b) If the rubber strain is not to exceed 0.2 in/in, determine the maximum allowable compressive force. Recall that the spring constant, k=Fx,or in terms of an axially loaded member
on five-cycle semilogarithmic paper plot the grain size distribution curves from the following mechanical analysis data
Testing has shown that at a local race track (0.25 in length) racecars have a maximum side friction factor of 0.08. The smallest turn radius on the oval track is 150 feet and has a banking of 20 degrees.
The engineer in charge of this project investigated severla alternatives to cool the exhaust gas and has concluded that the two most practical solutions would be either the installation of a waste heat boiler or the installation of a spray injecti..
fy=50000psi, f'c=3000 span of l=28 ft, dead load not including beam weight = 3 k/ft, live load=3 k/ft, p*=0.5pb, concrete weights=150 lb/ft cubed, use h=d+2.5 inch, assume beam weight =10kN/m and phi=0.90
The 1.2-Mg mine car is being pulled by winch M mounted on the car. If the winch generates a constant power output of 30 kW, and the car starts from rest, determine the speed of the car when t = 5s.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd