Calculate the heat transfer required to do quality in btu

Assignment Help Civil Engineering
Reference no: EM13307929

A rigid 1ft^3 vessel contains R-134a originally at -20F and 27.7% quality. The refrigerant is then heated until its temperature is 100F. Calculate the heat transfer required to do this, in Btu.

Reference no: EM13307929

Questions Cloud

What will be degree of consolidation reached at that time : Average pore water pressure in fully saturated clay specimien, which was subjected to a pressure of 20N/cm^2 initially, was measured to be 7N/cm^2 after a period of time.
What one characteristic about standard normal distribution : What one characteristic about the Standard Normal Distribution make it different from any normal distribution How do the standard deviation of 1 makes it diffenert. Can you plz explain? Do it some how throw the base answer off?
Compute the phase angle of the circuit : An RLC circuit is set up with a 350 mH inductor, a 6.8 mF capacitor and a 550 W resistor. What is the phase angle of the circuit
Demonstrate the both the commit and the rollback : Write a script to test your procedure. Demonstrate the both the commit and the rollback.
Calculate the heat transfer required to do quality in btu : A rigid 1ft^3 vessel contains R-134a originally at -20F and 27.7% quality. The refrigerant is then heated until its temperature is 100F. Calculate the heat transfer required to do this, in Btu.
Determine the temperature of the cold reservoir : A Carnot engine has an efficiency of 18.2%. It operates between constant-temperature reservoirs differing in temperature by 138 C °. determine the temperature of the cold reservoir
What is the emf induced in the rectangular loop : A rectangular loop of N turns and of length a and width b is rotated at a frequency f in a uniform magnetic field B. What is the emf induced in the rectangular loop
Sex education to middle age group is not good : Write 1500 to 1800 that giving sex education to middle age group is not good
Apply economic concepts to real world applications : Relates to content and skills covered in Week 7 of the Weekly Study Program, Chapter 32 of Ganset al. (2012). Refer here to the comments given for Week 7 for assistance in answering this question.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is velocity of blocks 5 after blocks started moving

What is the velocity of the blocks 5.00 after the blocks have started moving. Assume that the rope joining the two blocks in long enough so that, at this time, block A is on the frictionless surface while block B is still on the rough surface.

  Determine the maximum distortion energy theory of failure

At a certain location on the surface of an engineering component, the material is in a state of plane stress with principal stresses of fmax = 150 MPa and fmin = 50 MPa (both tensile). If the yield strength of the material is Y = 350 MPa

  Calculate the pressure in point 1 and the density of fluid

A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.

  Calculate average f per m using an mlss of 1000 mg per l

Wastewater flow is 80 gpcd with 170 mg/l BOD and 190 mg/l suspended solids. Size the extended aeration basin and clarifier using the minimum detention time and overflow rates. Calculate the average F/M using an MLSS of 1000 mg/l.

  Calculate the total axial deformation in the aluminum rods

A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel. The two rods to the right R1 and R2 are made of aluminum.

  Find coefficient of kinetic friction if car comes to stop

A classic car is d riving down an incline at 60 km / h when its brakes are applied. Treating the car as a particle, neglecting all forces except gravity and friction, and assuming that the tires slip

  What is the theoretical rate of moisture removal from grain

A model grain dryer is being used to investigate the drying process. It is discovered that the load cell which supports the dryer indicates that the mass of the dryer and its contentsinitially increases during the heat-up.

  Determine lowest temperature at which 2-mm gap is closed

At a temperature of 9°C, a 2-mm gap exists between two polymer bars and a rigid support. Bars (1) and (2) have coefficients of thermal expansion of t1 = 102 x 10-6 /°C and t2 = 66 x 10-6/°C, respectively.

  Find the net force required to hold the bend in place

A 1m diameter pipe bend is carrying water with a steady flow rate of 2 m3/s. The bend has an angle of 90o and lies in a horizontal plane. The volume of water in the bend is 1.5 m3 and the empty weight of the bend is 4 kN.

  Determine what is the height of the pure water column

a closed tank contains two straified non misicble fluid layers and compressed air. the fluid of the tank is saline water (relative density 1.036) with a total depth of 3.5m. the top fluid layer is oil (relative density of 08.2) with a depth of 0.6..

  Measure the distance pa, pb, pc

Measure the distance PA, PB, PC etc. from p to various point with chain or tape and plot them to scale along the co responding rays. Join the points a, b, c, etc. to give outline of survey.

  Determine maximum speed of the free fall for the sky driver

A sky diver with a mass of 75 kg jumps from an aircraft. The aerodynamic drag force acting on the sky diver is known to be Fd = kV^2, where k = 0.228. Determine the maximum speed of the free fall for the sky diver and the speed reached after 100 m..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd