Calculate the efficiency of the motors at the conditions

Assignment Help Electrical Engineering
Reference no: EM13226600

some permanent magnet DC motor calculations based on the NXT motors. If these motors are used without the encoders and operated at full speed they function as permanent magnet DC motors with approximately the following parameters: (assuming you didn't include external gearing).

No Load Speed: 163 rpm

No Load Current: 60 mA

Stall Torque: 40 N?cm

Stall Current: 1.26 A

a) Determine an equation for angular velocity,  (in rad/sec) versus Torque (in Nm).

b) Determine an equation for current (in amps) versus Torque (in Nm).

c) Based on these equations, determine the maximum power point. This is the value of and T that result in maximum power. State the power and the (,T) values. Do not assume this happens at 0.5T. The best way to do this is to make an Excel spreadsheet.

d) Based on these equations, determine the maximum efficiency point. This is the value of ? and T that result in maximum efficiency. State the efficiency and the (,T) values. Assume the battery is operating at 9 Volts. Do not assume this happens at 0.25T.

e) If the battery is replaced with a 6 Volt battery it was experimentally determine that the no load speed is reduced to 120 rpm. For this situation, determine a new equation for angular velocity,  (in rad/sec) versus Torque (in N?m).

f) Determine the theoretical maximum linear speed of your robot if the following assumptions are made:

I. A 9 Volt battery powers the motor so you use the derived equations from parts a) & b)

II. Your robot weighs 8 lbs. and the weight is evenly distributed over a 2 wheel vehicle with each wheel connected to a separate motor.

III. Assume your speed is measured at a situation where the vehicle is moving on level ground and rolling friction ?r is the only friction that is included in the calculation. Assume the robot is moving on pavement with a r value of 0.015. Assume your robot is pushing an object that weighs 2 lbs.

IV. You are using wheels that are two inches in diameter.

g) Calculate the efficiency of the motors at the conditions of part f.

Reference no: EM13226600

Questions Cloud

Critically evaluate the financial instruments : Critically evaluate the financial instruments available for investments and analyse and evaluate the role and influence of the main actors in financial markets, both private and public.
Determine the resistance of the rheostat in rotor circuit : A three phase, 25-hp, 440-V, 60-Hz, 1750 rpm, wound-rotor induction motor has the following equivalent circuit parameters:R1=0.20 ohms, X1=1.0 ohms, R2=0.15 ohms, X2=0.8 ohms, Xm=30 ohms The motor is connected to a three phase, 440-V, 60-Hz supply.
Which organizational constraints were factors in decision : In each of the three cases discussed here, which organizational constraints were factors in the decisions made?
Explain the mass balance equation for an fe3(po4)2 : Select each side of the mass balance equation for an Fe3(PO4)2 solution where the existing species are Fe2 , PO43-, HPO42-, H2PO4-, H3PO4, FeOH?
Calculate the efficiency of the motors at the conditions : Based on these equations, determine the maximum power point. This is the value of and T that result in maximum power. State the power and the (,T) values. Do not assume this happens at 0.5T. The best way to do this is to make an Excel spreadsheet.
The acqueous solution to determine the equilibrium constant : Calculate, in sequence each of the following quantities in the acqueous solution to determine the equilibrium constant for the reaction: a) mole of FeNCS+2 the form in the reacting equilibrium
Review the genetic information nondiscrimination : Analyze the cases under study in this document by addressing this question: "Should the court have invalidated civil rights as it did or did the court make a poor decision?" Explain your answer.
Describe the concentration of a to decrease : Products is second order with a rate constant of 0.469 M-1s-1. If the initial concentration of A is 0.159 M, how many seconds would it take for the concentration of A to decrease to 5.12 * 10-3 mol/L?
State the band would be filled with electrons : what fraction of the band would be filled with electrons? Assume that all valence bands (5s, 4d, and 5p) overlap. Show your work and your resulting band diagram.

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Find out the minimum signal to noise ratio

Determine the minimum signal to noise ratio (s/n) in dB required in each communication channel to achieve a data rate of 270 kbps?

  Explain c program that generates one hundred random

C program: counting numbers between 0-9, Write a C program that generates one hundred random integers between 0 and 9 and displays the count for each number.

  Explain eigenfunctions and lti systems

Eigenfunctions and LTI systems, The eigenfunction property is only valid for LTI systems. Consider the cases of nonlinear and of time varying systems.

  Determine the hv-side fuses needed to protect

Determine the HV-side fuses needed to protect a 3x140kVA, 12470/208 YNyn0 distribution transformer bank. Show and explain step by step the procedure you employ to solve this question. Use the type K and type T fuse curves

  Determine whether the signals are period

Determine whether the follow signals are period and for those that are find the fundamental period. F: x(t) = cos(t)u(t) G: x(t) = v(t) + v(-t) where v(t) = cos(t)u(t) I: x[n] = cos((1/5)(pi)(n)) * sin((1/3)(pi)(n))

  Will ohsas pel be exceeded

A plant has two identical standby generator units for emergency power use. In the area of the generators, the normal noise level registers 81 dBA on the sound-level meter with the generators turned off. When one generator switches on, the noise le..

  Determine the awg size of the extension cord

The resistance per 304.8 m of copper wire uses in the extension cord of AWG 14,12,10,8 and 6 are 2.58,1.62, 1.02, 0.64 and 0.41 respectively. Assume a 2% allowable voltage drop. Show all working .

  Determine the majority and minority carrier concentrations

A junction employs Nd = 8x 10^17cm^-3 and Na= 2 x 10^ 17 cm^-3. The device is at 300K. (a) determine the majority and minority carrier concentrations on both sides (b) Calculate the built-in potential at (i)T=250K (ii)300K

  Electrical and instrumentation use

Electrical & Instrumentation Use, State typical values for the loading effect on a low voltage AC circuit containing a lamp when measuring current with

  Sketch the circuit schematic with flip-flops

A ripple carry adder is made of full adder cells each having 1 unit of combinational delay. To convert a four-bit ripple carry adder into a four stage pipeline adder proceed as following.

  Saw on internet some equations to convert from frequency

Saw on internet some equations to convert from frequency in hertz to mph. Some equations need a gear ratio while others do not. I found the equation mph = circumference * RPM * 60.

  Find the probability of bit errors occurring in the frame

Let the probability of a bit error be p, and the length of a data frame be N. Find the probability of 1, 2, 3, and 4 bit errors occurring in the frame. a) Tabulate the results for N = 1000, 10000, and 100000 bits, for p = 10-6, 10-8, and 10-14

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd