Calculate the discharge in each pipe and the pressure

Assignment Help Civil Engineering
Reference no: EM13303055

Two reservoirs are connected with a 30" diameter pipe with a length of 19,680 ft. The water surface elevation in the upper reservoir of the upper reservoir is 984 ft, lower reservoir 886 ft and the elevation at the midpoint is 918 ft. To increase the capacity of the pipe line, a second 12" diameter pipe was installed from the upper reservoir to the center of the line (9,840 ft). Pipe friction is the same for all three pipes (f=0.02). Calculate the discharge in each pipe and the pressure at the midpoint.

Reference no: EM13303055

Questions Cloud

Which table in the back of the text provides the energy data : For each of the following, draw both the p - v and the T - v diagrams showing the location of the state and write below the diagrams a) what the condition the H2O is in (eg. Superheated vapor), b) which table in the back of the text provides the e..
At what temperature will condensation start to occur : A closed, rigid container with a volume of 1 m3 contains H2O initially at a pressure of 800 kPa and temperature of 500 C. Heat transfer occurs to the surroundings. At what temperature, in deg C, will condensation start to occur
Determine the the volume percentage of each metal : An object (it could be the crown that Archimedes had studied) made of gold and copper has a mass of 5.00 kg. determine the the volume percentage of each metal
Calculate the duration of a one-year fixed payments loan : Calculate the duration of a one-year fixed payments loan with monthly payments of $150 and yield to maturity of 12%. Use this number to determine the % change in the price of this loan if interest rates increase to 14%.
Calculate the discharge in each pipe and the pressure : Two reservoirs are connected with a 30" diameter pipe with a length of 19,680 ft. The water surface elevation in the upper reservoir of the upper reservoir is 984 ft, lower reservoir 886 ft and the elevation at the midpoint is 918 ft.
What is the de broglie wavelegth of this bacterium : A bacterium (mass = 2 × 10-15 kg) in the blood is moving at 0.28 m/s. What is the de Broglie wavelegth of this bacterium
Design temperature and residence time have been established : Assume that the design temperature and residence time have been established as 1300 degrees F and 0.6 seconds, respectively. The type of burner used in the process requires outside air at a mass ratio of 12:1 (air to fuel gas).
Determine at what speed is the ball moving : A photon of red light (wavelength = 710 nm) and a Ping-Pong ball (mass = 2.10 × 10-3 kg) have the same momentum. At what speed is the ball moving
In what respect is a perpetual bond similar to a no-growth : Are there preferred stocks that are evaluated similarly to perpetual bonds and other preferred stocks that are more like bonds with finite lives? Explain.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Find the strain develope in the sample

a quartzite sample in a compression testing mechine is 180mm long and 54mm in diameter. what is the stress under a load of 100kN? if the modulus of elasticity is 102kN/mm2, find the strain develope in the sample.

  How long would it be before company could sell the property

A multinational engineering consulting firm that wants to provide resort accommodations to certain clients is considering the purchase of a three-bedroom lodge in upper Montana that will cost $250,000.

  Determine what must the pipe diameter be

If a flow of 5.0 cfs is to be carried by an 11000 ft cast-iron pipeline without exceeding a head loss of 137 ft, what must the pipe diameter be

  Comparison between steel structures

Comparison between steel structures and aluminium structures, To make a comparison between Eurocode 3 and Eurocode 9 outlining the main differences

  Explain about pres-stressed concrete

Explain about pres-stressed concrete

  Source and destination addresses of router solicitation

Source and destination addresses of router solicitation, Given an IPv6 network, assume a host using EUI-64 addressing has a MAC address of00:24:E8:3D:CA:35

  Calculate the amount of co produced in a rich combustion

Assume the only products are CO2, H2O, CO and N2. State results as the CO molar fraction of both wet and dry exhaust products ( wet exhaust products include H2) and dry exhaust products exclude it).

  Calculate the engineering stress for the bar

Calculate the following for the bar:a) engineering stress at 0.001 (0.1%) strain, b) elongation, c) Young's modulus, d) final diameter of the bar Note: Poisson's ratio is 0.31 for 4140 steel, e) true stress, f) true strain.

  Design temperature and residence time have been established

The oven exhaust gases are available at 250 F. Assume that the design temperature and residence time have been established as 1300 F and 0.6 sec, respectively. The type of burner used in the process requires outside air at a moass ratio of 12:1

  What is the level of the service

If the peak-hour factor is .90 and all of the drivers are regular users, what is the level of the service of this compound-grade freeway segment?

  What will be the total vehicle delay

Assuming D/D/1 queuing, what will be the total vehicle delay?

  What is the minimum coefficient of road adhesion needed

The owners wish to achieve an initial acceleration from rest of 22 ft/(sec^2) on a level paved surface. What is the minimum coefficient of road adhesion needed to achieve this acceleration

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd