Calculate the design rate of super elevation

Assignment Help Civil Engineering
Reference no: EM13562472

A simple highway curve is planned to connect two horizontal tangents that intersect at sta. 2500+00.00 at an external angle of 52°.  For a design speed of 60 mi/h and a curve radius of about 1.25 times the minimum allowable, calculate (a) the design rate of superelevation and (b) the required length of superelevation runoff.  Assume a four lane undivided highway and 10-ft lanes.  Clearly state any other assumptions that you think are needed.

Reference no: EM13562472

Questions Cloud

Evaluate what wavelength of light is being used : A 3690-line/cm grating produces a third-order fringe at 21.4deg angle. What wavelength of light is being used
Determine the alkalinity and ph of the mixture : Two waters are in equilibrium with air, one at pH 9.5 and one at pH 7.3. these waters are mixed in 1:1 proportions. Assuming that carbonate species dominate the acid/base behavior of boh solutions and that no gas transfer occurs when they are mixed
What is the orbital velocity of particles : If you observe light reflected from Saturn's rings, youshould see a redshift at one edge of the rings and a blueshift atthe other edge. what is the orbital velocity of particles at the outer edge of the rings
Find what is the velocity of cars after they stick together : an car mass 1000kg is traveling east30m/s . it is hit by another car 2000kg whick was travelingnorthwest at 20m/s.the two cars stick together. what is the velocity of the cars after they stick together
Calculate the design rate of super elevation : A simple highway curve is planned to connect two horizontal tangents that intersect at sta. 2500+00.00 at an external angle of 52°.  For a design speed of 60 mi/h and a curve radius of about 1.25 times the minimum allowable
What is the probability in each year that a flood : The annual maximum series of flood magnitude in a river has a normal distribution with a mean of 6000 m^3/s and a standard deviation of 800 m^3/s
Determine the total delay maximum queue length and the time : Vehicles arrive at a tollbooth according to the function h(t)= 5.2-0.2t, where h(t)is in vehicles per minute and t is in minutes. The toll booth operator processes 3 vehicles per minute. Determine the total delay, maximum queue length, and the time i..
Calculate the circulating load of cleaner tailings : A froth flotation process is used to concentrate copper ore. It is a two stage process with a rougher stage followed by a cleaner stage. The cleaner tailings are returned to the rougher flotation. Both stages are non-reactive unit operations and both..
When is the rider going to reach the stopping point : If we apply a breaking system to a skateboard while the speed of the skateboard is 5Milies per hour, the rider average weights is 180bounds while his height is 170 cm

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute permeability in ft per second on cylindrical sample

A lab experiment of permeability test was carried out on a cylindrical sample of sand 3 inch in diameter and 4 inch in height. 9 in3 of water was collected in 2 minutes, under a head (water level difference) of 11 inch. Compute the permeability in..

  How to determine the scale reading at t

A large tank is used to calibrate the reading from a flow meter. Measurements of the system weight as a function of time are made. Water enters the tank vertically from the flow metering system at a speed of 20 ft/sec through a 1.5 in.

  Explain what is the hydraulic residence time of the river

An industry is illegally discharging benzene into a river. The concentration in the river at the point of discharge is 0.2 mg/L. A drinking water treatment plant (DWTP) is located 1.5 km downstream. The water velocity in the river is 0.35 km/day.

  Determine the maximum bending stress on the outside surface

A concentrated moment is applied to the free end. Determine the maximum bending stress on the outside surface of the cylinder and the maximum bending stress on the inside surface of the cylinder.

  Calculate the coefficient of volume compressibility

In an oedometer test, the void ratio of a clay sample changed from 1.62 to 1.41 as the vertical effective stress imposed on the sample was increased from 100 kPa to 200 kPa. Later on, the vertical effective stress on the sample was decreased

  What is the effective interest rate

A student bought a $75 used guitar and agreed to pay for with a single $85 payment at the end of the 6 months. assuming semiannual (every 6 months) compounding, what is the normal annual interest rate? what is the effective interest rate?

  Determine magnitude of velocity and acceleration of particle

The motion of a particle on the surface of a right circular cylinder is defined by the relations, R = A, theta = 2pi(t), and z=Bsin(2pi)(nt), where A is a constant. Determine the magnitudes of the velocity and acceleration of the particle at any t..

  Calculate the maximum temperature and maximum pressure

in an air standard otto cycle , the air at the beginning of the compression stroke is at 95 kpa and 22c ,and the cylinder volume is 0.0028 m^3 . the compression ratio is 9 and 4.3 kj are added during the heat addition process

  Determine the required mass of c and the length of the cable

if D has a mass of 600 kg, determine the required mass of C, the maximum sag h of the cable, and the length of the cable between the pulleys A and B. The Beam has a mass per unit length of 50 kg/m.

  Calculate the horizontal force required to hold the hose

A fire hose and nozzle have the following characteristics. Diameter of the hose and the nozzle are .25ft and .1ft respectively. If the pressure inside the hose is 60 psig and the flowrate is 1.2 ft^3/s,

  Usage rates if the community has a declining growth rate

Determine how many years from now the consumption will reach its design capacity with current usage rates if the community has a declining growth rate.

  Compute gravimetric water content and buoyant unit weight

A sample of clay was obtained from a point below the water table. An oven-drying test performed on this sample resulted in the following data: Mass of can= 10.88 g Mass of can + wet soil = 116.02 g

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd