Reference no: EM13714075
A load test on a 8-mm diameter by 375-mm long aluminium alloy rod found that a tension load of 4800N caused an elastic elongation of 0.52-mm in the rod. Using this result, determine the elastic elongation that would be expected for a 23-mm diameter rod of the same material if the rod were 1.2m long and subjected to a tension force of 23kN.
Part 1: Calculate the cross-sectional area of the test rod with a diameter of 8mm.
Part 2: Calculate the normal stress in the test rod with a diameter of 8mm due to the 4800N-test load.
Part 3: Calculate the normal strain in the test rod with a diameter of 8mm due to the 4800N-test load.
Part 4: Calculate the elastic modulus of the aluminium alloy. Assume the material is exhibiting elastic behaviour.
Part 5: Calculate the cross-sectional area of the rod with a diameter of 23mm.
Part 6: Calculate the normal stress in the rod with a diameter of 23mm due to the 23-kN load.
Part 7: Calculate the expected strain in the rod with a diameter of 23mm produced by the 23-kN load.
Part 8: Calculate the expected elongation in the rod with a diameter of 23mm produced by the 23-kN load.
Determine the heat transfer input required for the heat
: A Carnot heat engine produces power of 2.5 kW. It rejects heat to a river that is flowing at 2 kg/s, resulting in a temperature increase of 2° C. The average temperature of the river is 20° C.
|
Amplitude of the excitation provided to the machine
: A 45 kg machine is mounted on a spring of stiffness 8x10^5 N/m. When the machine is set to vibration by a 32 Hz excitation, the machine's amplitude is measured as 1.5mm. What is the amplitude of the excitation provided to the machine? Ignore damping ..
|
Refrigeration system-determine the temperature and quality
: R-410a flows at 0.3 Ibm/s in a refrigeration system. The R-410a is throttled from 60 F. 270 psia to 45 psia. Determine the temperature and quality of the R-410a after throttling.
|
Find the maximum length of the specimen before deformation
: A cylindrical specimen of a titanium alloy having an elastic modulus of 107 GPa and an original diameter of 4.0 mm will experience only elastic deformation when a tensile load of 1,500 N is applied. Find the maximum length of the specimen before defo..
|
Calculate the cross-sectional area of test rod with diameter
: A load test on a 8-mm diameter by 375-mm long aluminium alloy rod found that a tension load of 4800N caused an elastic elongation of 0.52-mm in the rod. Using this result, determine the elastic elongation that would be expected for a 23-mm diameter r..
|
Calculate back pressure to locate shock at the exit plane
: Air at a stagnation pressure 700kPa flows isentropic ally through a convergent-divergent nozzle. The design pressure at the nozzle exit is 56 kPa. If the back pressure is raised gradually, thereby creating a shock in the divergent portion of the nozz..
|
Meteorologist is studying hurricanes and tornadoes
: A meteorologist is studying hurricanes and tornadoes. She determines that a particular historic tornado can be described by phi7. At a distance 1 km from the eye of the tornado (the eye is at the origin of the coordinate system) the radial velocity i..
|
Determine the following for a south facing surface
: Determine the following for a south facing surface at 30° slope in Gainesville, FL (Latitude = 29.68°N, Longitude = 82.27°W) on September 21 at noon solar time (Assuming a ground reflectivity of 0.2):
|
Estimate the radiation reaching the earth!
: Please use the radiation fundamental and sun’s size to recalculate the sun radiation power and mass loss rate. Please also estimate the radiation reaching the earth!
|