Calculate the angular acceleration of link ab and link bc

Assignment Help Civil Engineering
Reference no: EM13318371

If OA has a constant counterclockwise angular velocity of 10rad/s, calculate the angular acceleration of link AB and link BC for the position where the cordinates of A are x=-60mm and y = 80mm. Link BC is vertical for this position.

Reference no: EM13318371

Questions Cloud

Purpose of the uniform commercial code : What is the purpose of the Uniform Commercial Code (UCC)? What types of transactions are covered by the UCC? What problems was the UCC designed to address? How would interstate transactions be different without the UCC?
What is the numerical value of the average error : What is the numerical value of the "average" of the sampling distribution and what is the numerical value of the "average error" for each data point in the sampling distribution
Identify which specific employees should do what : Identify two major control weaknesses in the Family Support Center's cash receipts procedures. For each weakness you identify, suggest a method to correct that weakness. Your solution must be specific-identify which specific employees should do..
What is the ac input voltage : A resistance R and a 1.5-H inductance are in series across a 60-Hz ac voltage. What is the ac input voltage
Calculate the angular acceleration of link ab and link bc : If OA has a constant counterclockwise angular velocity of 10rad/s, calculate the angular acceleration of link AB and link BC for the position where the cordinates of A are x=-60mm and y = 80mm.
Suffers from debilitating arthritis : Hazel is 84, and suffers from debilitating arthritis. Sometimes, she can barely walk. Every time Hazel has been unable to get around, her neighbor Ruth cooks and cleans for her until she feels better
Explain temperature change (in k) will be needed to change : A gas occupies 5.38 L when the temperature is 45.0oC and at 1.00 atm of pressure. What temperature change (in K) will be needed to change the volume to 6.30 L at constant pressure
Find the magnitude of the magnetic flux through the coil : A circular coil of wire with 200 turns and a radius of 30 cm is laying flat on a horizontal wooden table. find the magnitude of the magnetic flux through the coil
Calculate the overflow rate and effulent weir loading : A wastewater treatment plant has two rectangular primary settling tanks, each 40 ft long, 12 ft wide, and 7 ft deep. The effulent weir length in each tank is 45 ft. The average daily wastewater flow is 387,000 gal.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the deflection in degree for horizontal wind speed

Determine the deflection in degrees for horizontal wind speed of 10m/s and what is the magnitude of the force required at the bottom of the sign to prevent the sign from deflecting

  Find the minimum weight need to keep the gate closed

plane gate of uniform thickness holds back a depth of water. Find the minimum weight need to keep the gate closed. theta=30degrees L = 3m w = 2m

  Maximum rod diameter on lathe machine

If the tensil testing machine can apply no more than 925 lbs. of force to the specimen, calculate the maximum rod diameter that should be used. (precision 0.000)?

  Calculate what will be the total emissions of pm and pm10

emissions from waste oil combustion may be estimated using ap-42 1.11. A small boler is operated from 10/15/2012 through 4/15/2013 and it is used to burn 45 gallons per hour of a blended waste oil having an ash content of 7%

  What is the probability it will be equaled or exceeded

A 1.2-in. rainfall occurs in a 6-hour duration. If this represents an exceedence probability of 10%, what is the probability it will be equaled or exceeded at least once in the next 3 years. What is the probability it will be equaled or exceeded e..

  Determine what will be the new height of fluid column

A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the manometer is 12.0 g/cm3.

  Determine what is the speed in rpm of the car wheels

If a car engine is turning at 4000 rpm, the transmission gear ratio is 3:1 and the final drive ratio is 4:1. (a) what is the speed in rpm of the car wheels and (b) the vehicle speed if the tire radius is 8 inches

  Calculate equivalent pipe size and flow in the pipe

The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m

  Structural health monitoring using guided wave propagation

Structural health monitoring using Guided Wave propagation for Detection and Evaluation of Flaws in Pipes.

  How to select economical solid rectangular timber beam made

A simply supported beam is to span 12 feet. It will support a uniformly distributed load of 800 pounds per linear foot over the full span and a concentrated load of 1000 pounds acting at 4 feet from the left support.

  Why are the pressure for different in fluid mechanices

why are the pressure for those p2/p1 different than whats given for question 3.2.3 in Fluid mechanices with engineering application 10ed

  Calculate the maximum shear and indicate in terms of x

a. Determine the shear and moment diagram. b. Calculate the maximum normal stress on the top of the beam, on the bottom of the beam and indicate in terms of x its location.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd