Calculate head supplied by the pump for the system

Assignment Help Civil Engineering
Reference no: EM13319436

Water from a lower reservoir (water surface elevation) 500 m is pumping to the upper reservoir (water surface elevation 600 m) through a 5000 m long straight pipe with 0.5 m diameter. If the flow rate is 1m3/s, calculate head supplied by the pump. Draw HGL and EGL for the system. Assume the water depth in the lower reservoir is 5 m and the depth in upper reservoir is 10m. The pump is located close to the pipe entrance at the lower reservoir.

Reference no: EM13319436

Questions Cloud

With what minimum speed must he drive off horizontal ramp : A stunt driver wants to make his car jump over 8 cars parked side by side below a horizontal ramp as seen in the figure below. With what minimum speed must he drive off the horizontal ramp to just barely make it across
Define what is the ph at the equivalence point : What is the pH at the equivalence point when when 40.0 mL of 0.183 mol/L HC7H5O2(aq) is titrated with 0.131 mol/L NaOH(aq)? Assume the temperature is 25oC
Design the beam in us customary units using f : Design the beam in US customary units using f'c=4ksi and fy=413.4MPa. If necessary use d'=2.5in. Assume an exterior exposure according to ACI 318 and b=15in.
Explain with two significant digits : For a solution that is 0.282 M NH3 and 0.117 M NH4NO3, calculate the following. For NH3, Kb is 1.8x10-5. Enter [OH?] and [H3O+] with two significant digits. Enter scientific notation as 1.23E4.
Calculate head supplied by the pump for the system : Water from a lower reservoir (water surface elevation) 500 m is pumping to the upper reservoir (water surface elevation 600 m) through a 5000 m long straight pipe with 0.5 m diameter.
The firm is proposing to buy a new plant which can generate : The firm is proposing to buy a new plant which can generate additional annual profit of Rs. 10,000. The fixed costs of new plant is expected to Rs. 4000. The new plant will increase the sales volume by Rs. 40,000. It can be assumed that the ratio bet..
Explain what is the final ph of the solution : What is the final pH of the solution when 15.0 mL of 0.121 mol/L NaOH(aq) and 35.0 mL of 0.181 mol/L HNO2(aq) are mixed? Assume the temperature is 25oC.
Estimate settlement of footing four years after construction : The modulus of elasticity of the sand was determined to be 10,000 kN/m^3 throughout. Using the Schmertmann's method, estimate the settlement of the footing four years after construction, using four 1 meter thick sublayers.
Explain the ph of a 0.175 mol/l solution of sodium acetate : What is the pH of a 0.175 mol/L solution of sodium acetate, CH3COONa, at 25oC? (pKa=4.74 at 25oC for CH3COOH.) Give your answer accurate to two decimal places

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Calculate depth h of mud for the concrete retaining wall

calculate the depth h of mud for which the 3m concrete retaining wall is on the verge of tipping about its forward edge A. the density of mud may be taken to be 1760 kg/m3 and that of concrete to be 2400 kg/m3.

  Determine the vertical force p exerted by the tower on pin a

a transmission tower is held my three guy wires attached to a pin at A and anchored by bolts b c and d if the tension in wire ab is 3.6 kn determine the vertical force p exerted by the tower on the pin at A

  Calculate the normal strain using poissons ratio

If the normal stress is 2,500 psi, Poisson's ratio is 0.25 and Young's modulus is 10,000 ksi, calculate the normal strain.

  Find coefficient of kinetic friction if car comes to stop

A classic car is d riving down an incline at 60 km / h when its brakes are applied. Treating the car as a particle, neglecting all forces except gravity and friction, and assuming that the tires slip

  Describe how shear stress due to the applied torque varies

A hollow circular shaft is loaded in pure torsion. Describe how the shear stress due to the applied torque varies on a cross section whose unit normal vector lies parallel to the long axis of the shaft.

  What is capacity of pump required to supply max discharge

What is the capacity of the pump required to supply maximum required discharge to the model, in CFS The length of time the model must be operated to check the equivalent of 36 hours of operation for the prototype operation, in decimal format hours..

  Estimate shaft elongation in millimeters with applied force

A 4.00-cm-diameter, 0.80-m long rod of aluminum 7075-T6 is subjected to an axial tensile force with a factor of safety of 1.75. The yield stress and modulus of elasticity of aluminum 7075-T6 are 500. MPa and 210. GPa, respectively.

  Determin the force in memebers de-hg and he of the stress

determin the force in memebers de, hg and he of the trees and state if the members are in comperhemsion

  Geometric design and construction of a new two-lane road

Geometric design and construction of a new two-lane two-way road has been recently completed and now it is time for design pavement near Ballarat, Victoria.

  Determine what is the drag coefficient at the cars top speed

A 3000-lb car has a maximum speed (at sea level and on a level, paved surface) of 140 mi/h with 16" radius wheels, a gear reduction of 3.5 to 1, and a drivetrain efficiency of 92%. It is know that at the car's top speed the engine is producing 220..

  How many years will it take to uniformly corrode a thickness

A galvanized (zinc-coated) steel sheet is found to uniformly corrode with an average current density of 1.4 X 10-7 A/cm2. How many years will it take to uniformly corrode a thickness of 0.030 mm of the zinc coating

  Find second year book value for equipment with initial cost

what is the second year book value for equipment with an initial cost of $11,000, a salvage value of 1,000 and a recovery period of 5 yrs for A. straight line depreciation. B. Double declining balance. C. MACRS

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd