Calculate electric power input to oven per unit oven width

Assignment Help Mechanical Engineering
Reference no: EM13702471

The electric reheating oven is used to heat a continuous sheet of metal from 25-1000C The metal speed is such that the strip of metal spends 2 hours inside this oven, The sheet thickness is 1cm and the ambient temperature is 25C with the temperature of the outside of the oven a uniform 50C. Inside the oven use a h_convection= 20 W/ m^2*K and the metal sheet is 304 ss. Calculate the electric power input to the oven per unit oven width; q'. What percentage of this power is lost by convection to the outside air?

Reference no: EM13702471

Questions Cloud

What is the power requirement of the compressor : Methane gas is compressed at the rate of 3x104 m3/hr (as measured at 0.1013 MPa and 15C) from 0.69 MPa and 26.7C to 3.45 MPa. The compressor operates adiabatically and has an efficiency of 80%. After compression, the methane is colled at a constant p..
Unix uses many commands in its operating system : Question 1: UNIX uses many commands in its operating system. Research on the web at least 2 more commands describe their function and discuss similar commands in Windows operating system.
Determine relative humidity-humidity ratio and the enthalpy : Atmospheric air at a pressure of 1 atm and dry-bulb temperature of 90F has a wet bulb temp of 85F. Using the psychometric chart, determine (a) the relative humidity, (b) the humidity ratio, (c) the enthalpy, (d) the dew point temp and (e) the water v..
Refraction of a light beam at the interface of two media : The following is a diagram shows refraction of a light beam at the interface of two media. The incidence and refraction angles are measured to be 45 deg and 30 deg respectively. Will total reflection happen when the light beam shins from the top to t..
Calculate electric power input to oven per unit oven width : The electric reheating oven is used to heat a continuous sheet of metal from 25-1000C The metal speed is such that the strip of metal spends 2 hours inside this oven, The sheet thickness is 1cm and the ambient temperature is 25C with the temperature ..
District heating system should supply hot water : If the district heating system should supply hot water at 900C, what is the lowest possible condenser pressure with water as the working sub-stance?
The end of the bar will be in contact with the frame : A 250mm long brass bar (CTE = 20.5X10-6 / 0 C) is being supported as shown below. Initially, when the temperature is 15 deg C, there is a total clearance of 0.25mm between the right end (left end is secured to the left side support) of the bar and th..
Calculate the electric power input to the oven per unit : The electric reheating oven shown in the figure is used to heat a continuous sheet of metal from 25-1000C The metal speed is such that the strip of metal spends 2 hours inside this oven, The sheet thickness is 1cm and the ambient temperature is 25C w..
The beginning the channel is idle : An ad Hoc network using IEEE802.11 has 4 nodes: N1, N2, N3, N4. Assume that SIFS is 1 unit of time, PIFS 2 units of time, DIFS 3 units of time, and slot time is 2 (these values are not the real values but are taken to simplify the packets sched..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Assuming the car accelerates from 0 to 59 mph at a constant

the 2007 bmw z4 coupe 3.0si can accelerate from 0 to 59 mph in 5 s and its maximum speed is 152 mph. assuming the car

  A natural gas engine has a bsfc of 9000 btushp-hour when

1. a natural gas engine has a bsfc of 9000 btushp-hour when producing 200 horsepower. how many btus per hour does the

  Determine for this machine the slip factor isentropic

a centrifugal compressor delivers 20 kgs of air at 0.32 mnm2 when running at 17500 rpm and absorbing 2800 kw. the inlet

  A constant pressure process results in a work output of 10

a piston-cylinder contains nitrogen at a temperature of 50 degc a pressure of 500 kpa and a volume of 10 liters. a

  Find the overall efficiency of the pump disregard friction

a storage tank is 40 feet above a river. water is pumped from the river to the storage tank at a rate of 0.095m3s. the

  Determine a t2 in 0r and b the rate of exergy destruction

air at t11300 0r p116 lbfin2 enters a counterflow heat exchanger operating at steady state and exits at p214.7 lbfin2.

  What is the rotation matrix for an object rotation

what is the rotation matrix for an object rotation of 30o around the z axis followed by 60o around the x axis and followed by a rotation of the y axis. all rotations are counter clockwise.

  Features are used to assess quality

Assume the same eight features are used to assess quality

  Determine head loss and the power required to overcome it

determine head loss and the power required to overcome it given efficiency 73 power of the pump 12hp height 35ft water

  Determine the temperature of the insulated surface of the

consider a large plane wall of thickness l 0. 5 m. the wall surface at x 0 is insulated while the surface at x l is

  Inlet 1 is a saturated vapor with a flow rate of 034 kgs

1 air at the inlet of a nozzle is at 500 kpa 42.2oc and a velocity of 87 ms. the nozzle exit pressure is at 132 kpa.

  A pile weighing 2000 lb is driven vertically into the

a pile weighing 2000 lb is driven vertically into the ground by a pile-driver hammer weighing 6000 lb which falls

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd