Calculate displacement-velocity-acceleration for assembly

Assignment Help Mechanical Engineering
Reference no: EM13708159

A certain piston cylinder assembly has a stroke of 85mm, a connection rod length of 130 mm and a piston pin offset of 2mm. Calculate the displacement, velocity and acceleration of the assembly operating at 2200 RPM. If the same configuration is used but the cylinder bore is offset by 10mm perpendicular to the axis of the crankshaft, calculate the displacement, velocity and acceleration for this assembly and compare it to the previous one. Why might one design an offset?

Reference no: EM13708159

Questions Cloud

Reduce the mass of an aluminium bulkhead for a spacecraft : In an effort to reduce the mass of an aluminium bulkhead for a spacecraft, a machinist drills an array of holes in the bulkhead. The bulkhead is a triangular-shaped plate with a base and height of 2.5 m and 1.6 m, respectively, and a thickness of 7 m..
Determine the axial stress required to induce this strain : An aluminium bar is subjected to uniaxial tensile loading. If the lateral strain (perpendicular to the load direction) is measured to be -0.00025, determine the axial stress required to induce this strain (round to the nearest ksi).
Maximum normal stress and the maximum shear stress : A thin walled tube with closed ends has an inside radius of 80mm and a wall thickness of 6 mm. It is subjected to an internal pressure of 20 MPa, a torque of 60 kN*m, and an axial compressive force of 200 kN. Determine the maximum normal stress and t..
Determine the volumetric flow rates at the inlet and exit : Refrigerant 22 enters an insulated compressor operating at steady state as saturated vapor at - 16 C with a mass flow rate of 1.5 kg/s. Refrigerant exits at 7 bar, 70 C. Changes in KE and PE from inlet to exit can be ignored. Determine: (a) the volum..
Calculate displacement-velocity-acceleration for assembly : A certain piston cylinder assembly has a stroke of 85mm, a connection rod length of 130 mm and a piston pin offset of 2mm. Calculate the displacement, velocity and acceleration of the assembly operating at 2200 RPM. If the same configuration is used ..
Drip irrigation problem : Drip irrigation is a means of getting water directly to growing plants with very little waste. One method uses a large-diameter polyethylene "mother" tube (10-15 mm i.d.) from which lead many small diameter polyethylene feeder tubes, called drippers,..
Block of copper at at initial temperature : A 25-kg block of copper at at initial temperature of 150 C equilibrates with 0.79 kg of liquid water at an initial temperature of 20 C in an insulated tank. If the average specific heat of copper can be taken to be 0.395 kJ/kg.K, determine the final ..
The raw material price and consumable price : Within the last month, the raw material price and consumable price combined has increased by 5.5%. If the throughput was 5 parts/hour estimates the future throughput that has to take place in order to maintain a constant production cost. Consider the..
Compressor is employed to compress gas : A compressor is employed to compress gas flowing steadily through it. The gas enters the compressor at a temperature of 16°C, a pressure of 100 kPa, and with an enthalpy of 391.2 kJ/kg. The gas leaves the compressor at a temperature of 245°C, a pre..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Draw the pressure vessel large enough to show orientation

A cylindrical pressure vessel of 120 in diameter outside, used for processing rubber, is 36 ft. long. If the cylinder portion of the vessel operates at 120 psi internal pressure, what are the stresses acting on an element at the inside surface of the..

  For other properties fixed in a rakine cycle raising the

for other properties fixed in a rakine cycle raising the condenser temperature causes what changes in the work and heat

  Determine the velocity of molten metal flowing through

How do you determine the velocity of molten metal flowing through the base of the downsprue?

  Two perfectely black squares 10 ft x 10 ft are spaced 20

two perfectely black squares 10 ft x 10 ft are spaced 20 feet apart. what is the net rate of heat exchange between them

  The relative acceleration of block d with respect respect

the system shown starts from rest and each component moves with a constant acceleration. if the relative acceleration

  Determine the maximum shear stress in the shaft

A 40 mm diameter hole is drilled 3 m deep into the steel shaft. When the two torque are applied, determine (a) the maximum shear stress in the shaft: and (b) the angle of rotation of the free end of the shaft. Use G= 83GPa for steel.

  An insulated piston-cylinder device contains 5 l of

an insulated piston-cylinder device contains 5 l of saturated liquid water at a pressure of 200 kpa. an electric

  Defining points and vectors of a parametric cubic curve

Find the equation of a Hermite cubic spline that passes through points (1, 1) and (3, 2) and whose tangent vectors are as follows: Sketch the curve and the blending functions for the defining points and vectors of a parametric cubic curve.

  Determine the heat and work associated with each process

a piston-cylinder device contains r-134a. initially the phase is saturated vapor at 160 kpa. the system then undergoes

  Determine the angle through which end d of shaft cd rotates

In the gear-and-shaft system shown, the shaft diameters are dab= 2 in. and dcd=1.5 in. Knowing that G = 11.2 x10^6 psi, determine the angle through which end d of shaft cd rotates.

  The electrical resistivity of 90wt cu-10wt ni cupronickel

the electrical resistivity of 90wt. cu-10wt. ni cupronickel alloy at room temperature is 16x10-8?.m. the electrical

  Write a c program calls a function to read a list of n

write a c program calls a function to read a list of n integer values from user input. if user inputs -999 the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd